background image

- Insert the small mounting bolt (B) through the mounting plate (D) hole and mounting bracket      

(E) hole. Tighten the bolt (B) securely. 

-  Firmly pull on the mounting plate (D) to verify it is securely attached to the mounting bracket  

(E).   

Step 3. Marking the electrical connections

- Insert the junction box wires into the side of the terminal block. 

       Insert the white wire from the junction box into the terminal marked “N (White)”.

       Insert the black wire from the junction box into the terminal marked “ L (Black)”.

       Insert the green ground wire from the junction box into the terminal marked “GND”.

Step 4. Mounting the light fixture

Align the bottom edge of the light fixture (A) with the bottom edge of the mounting plate (D).     

  Tilt the light fixture (A) toward the mounting plate (D), marking sure the light fixture (A) is             

  centered on the mounting plate (D). 

Tighten the large mounting bolt (H) securely through the center of the mounting plate (D). Do  

  not overtighten. 

Push the rubber plug (C) firmly into the large mounting bolt hole on the light fixture (A). 

Step 5. Caulking Around the Light Fixture

- Caulk around the canopy and mounting surface with silicone sealant (not included).

1.  Adjusting the Lamp heads and Sensor

-

 

Lamp heads can be adjusted easily. You may adjust the lamp head left and right or up and 

down to get the desired lamp direction.

-  Sensor can be adjusted easily. You may adjust the sensor left and right or up and down to 

get the desired lamp direction.

Note: For installing this light fixture on a covered wall or eave without junction box, 

please call the customer service number listed on the front and back cover of this 

manual.

Note: LED LAMPS ARE NON-REPLACEABLE. Do not attempt to access / maintain the 

LEDs; they are non-replaceable and any contact may damage the LEDs and will void the 

warranty.

INSTALLATION (Continued) 

INSTALLATION (Continued) 

OPERATION

45º

45º

80º

90º

40º

40º

25º

25º

25º

25º

45º

90º

25º

C

H

A D

06

07

Содержание AEC-5340







Отзывы: