background image

Owner’s Manual

7

General Precautions (cont’d)

Electrical Safety (cont’d)

z

All connections and conduits from the generator to the load must only be 
installed by trained and licensed electricians, and in compliance with all 
relevant local, state, and federal electrical codes and standards, and 
other regulations where applicable.

z

The generator must be earth-grounded for fixed installations in 
accordance with all relevant electrical codes and standards before 
operation.

z

Do not attempt to connect or disconnect load connections while standing 
in water, or on wet or soggy ground.

z

Do not touch electrically energized parts of the generator and 
interconnecting cables or conductors with any part of the body, or with 
any non-insulated conductive object.

z

Connect the generator only to a load or electrical system (110/120 volt) 
that is compatible with the electrical characteristics and rated capacities 
of the generator.

z

Before servicing equipment powered by the generator, disconnect the 
equipment from its power input.

z

Keep all electrical equipment clean and dry. Replace any wiring where 
the insulation is cracked, cut abraded or otherwise degraded. Replace 
terminals that are worn, discolored, or corroded. Keep terminals clean 
and tight.

z

Insulate all connections and disconnected wires.

z

Guard against electric shock. Prevent body contact with grounded 
surfaces such as pipes, radiators, ranges, and refrigerator enclosures.

Personal Safety

z

Stay alert. Watch what you are doing, and use common 
sense when operating a generator. Do not use generator 
while tired or under the influence of drugs, alcohol, or 
medication. A moment of inattention while operating 
generators may result in serious personal injury.

z

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. 
Keep your hair, clothing, and gloves away from moving parts. Loose 
clothes, jewelry, or long hair can be caught in moving parts.

Содержание HDP-3500





























Отзывы: