Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insert lower middle section (C) into the tree bottom (D). (See Fig. 2)
Step 3. Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Step 5. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the power cord into a proper outlet. Please note this tree
comes with a foot pedal switch for easy illumination.
User Servicing Instructions
Replace the lamp.
1.
Grasp plug and remove from its power source.
2.
Unlock the lock on the bulb socket.
3.
Pull bulb AND plastic base straight out of socket. Do not twist bulbs
while you are removing them.
4.
Replace burned-out bulb with 3 V, 20 mA LED bulb ONLY.
(Additional bulbs are included for your convenience.)
5.
Relock the lock on the bulb socket.
If the new bulb base does not fit in bulb holder, follow these steps:
Remove the cover.
Remove the base of the burned-out bulb
by straightening the bulb leads, and
gently pull bulb out.
Thread leads of new bulb through holes
in old base with one lead in each hole (always match the long lead of
new lamp to the hook of lamp base).
After bulb is fully inserted into base, bend each lead up so that the
leads will touch the contacts inside the bulb holder.
Insert the cover.
CAUTION
:
1.
To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2.
Risk of fire. This product does not contain lamp shunts, which allow the
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
3.
This product can only be used with the original adapter, not other
brands of adapter.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree neatly in a cool, dry place away from sunlight.
CAUTION! –
ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ATTEMPTING BULB REPLACEMENT.
Troubleshooting
Problem
Solution
The tree
does not light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is well connected to the
wall outlet.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Loose branches
1.
If a branch of the tree in section A, B or C falls off, follow the steps
below to reinstall it with a spare latch (G).
1)
Place the branch into the slot of the bracket.
2)
Insert a spare latch
through the hole and
use diagonal pliers (not
included) to crimp the
latch. (See Fig. A)
2. If a branch of the tree in section D falls off, follow the steps
below to reinstall it with a spare threaded iron latch (H) and two
retainer washers (I).
1) Place the branch into the slot of the bracket.
2) Insert a spare threaded
iron latch (H) through the
hole and secure using two
retainer washers (I). (See
Fig. B)
