Operation
Turning on the tree
NOTE: If some bulbs do not light or flicker, search for any loose, broken
bulbs and /or missing bulbs. Replace bulbs promptly with the
replacement bulbs provided in order to maintain the performance and life
expectancy of your tree.
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Maintenance
This product contains two different lamps, so there are two ways to
replace the lamps.
Replacing the low-voltage lamps
1.
Grasp plug and remove from its power source.
2.
Remove the reflector of the bulb.
3.
Pull bulb straight out of socket. Do not twist bulb.
4.
Replace burned-out bulb with 3.0 volt, 0.06 watt LED bulb ONLY.
Directly insert the LED bulb into the lamp holder.
5.
If the bulb doesn’t light up, change the LED bulb’s direction to insert
into the lamp holder (replacement bulbs are provided).
6.
Insert the reflector into the bulb.
BULB REPLACEMENT:
1.
Grasp plug and remove from its power source.
2.
Unlock the lock on the bulb socket.
3.
Pull bulb AND plastic base straight out of socket. Do not twist bulbs
while you are removing them.
4.
Replace burned-out bulb with 3 V, 0.06 W LED bulb ONLY.
(Additional bulbs are included for your convenience.)
5.
Relock the lamp lock on the bulb socket.
If the new bulb base does not fit in bulb holder, follow these steps:
Remove the base of the burned-out bulb by straightening the bulb
leads, and gently pull bulb out.
Thread leads of new bulb through holes in
old base with one lead in each hole.
After bulb is fully inserted into base, bend
each lead up so that the leads will touch the
contacts inside the bulb holder.
CAUTION! –
ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ATTEMPTING BULB REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the plug cord from the wall outlet. And remove your
adaptor cord and a foot pedal switch cord from bottom section (C)
and save them.
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are plugged into each
other and that the tree is plugged into the wall outlet.
Make sure the foot pedal switch and adaptor are well
connected to the bottom section (C).
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
