HOM Aneto, Инструкция по установке

Страница: 20 / 22

20
INSTRUCTION FOR USE
BEFORE USING THE PRODUCT

Please read these instructions carefully before beginning
installation to ensure the appliance is installed safety and
correctly.
 Installation should be performed by qualified professional
only. Local installation standards should be applied.

Before any operation remove the packaging and check
appliance integrity. If any defect or damage are noticed do
not install or try to repair the appliance but inform the
retailer.
The packaging should be kept out of reach of children and
disposed in accordance whit the national regulations for
waste processing.
 Do not modify or disassemble the appliance. It may cause
fire, electric shock or injury.

This appliance is designed and produced for home use only
and is not suitable for installing and using in public places
or on vehicles, boats or aircraft.
FOR YOUR SAFETY

Use a single-phase alternating current 230 V, 50 Hz power
supply. Voltage in excess of 230 V +10 % may cause
malfunction, so stay within the rated range.

Electrical wiring work should be done by a certified
professional in conformance with local standards.

Be sure to install a ground-fault circuit interrupter with idn
< 30 mA.

This is a CLASS I electric insulation appliance and must be
properly grounded.

If the electric cable or the plug are damaged and has to be
repaired do not perform this repair by yourself. Bring the
product to a qualified repair centre and have them repaired
by specialised personnel in order to avoid any risk of
damage.

Never use the product in rooms that are saturated with
explosive gas, vapours generated by solvents or paints or
any other flammable vapours or gas.
 This appliance is not intended for use by young people or by
persons who possess limited physical, sensorial or mental
capabilities unless they are adequately supervised by a
responsible person to ensure that they can use the appliance
safely. Young children should be supervised to ensure that
they do not play with the appliance.

Never allows animals or children to play with or touch the
appliance.

Attention! When turned on, the panel may become very hot.
 Attention this appliance is intended only for drying textiles
washed in water.

Never leave your home while the appliance is turned on;
make sure the illuminated switch is OFF and the red light is
off.
SAFE POSITIONING
 Never install the appliance on a surface made of wood or
synthetic material.
 Always place this appliance in vertical position so that the
supply cable results on the down side of it.

Do not climb on the appliance.
 Never place this appliance immediately underneath a power
socket.
 Always make observe the minimum distances from wall,
furniture or other objects as showed (fig. A, pg. 13).
 The appliance has a grade IPX1 water protection. The
product may be used in bathrooms or humid places as long
as the safety zones are respected and a permanent electrical
connection is performed. In any cases avoid installing the
appliance in location where there is a lot of condensation.
 It must never be possible for person in the bath tub or
shower to reach the power switch.
INSTALLATION

Expansion plugs and screws, provided with the product, are
only suitable for concrete or solid brick walls. For different
wall material types, use the appropriate fixing means.
ELECTRICAL CONNECTIONS
 The product must be powered at a voltage of 230 Vac, 50
Hz.
 The product is supplied, depending on type:
-
with a cable ending with Schuko IPX0 plug having an
integrated illuminated switch to connect to a proper
efficient earthed socket;
- with a 3 core cable for a permanent installation to the
main power supply by means wires with a min. section of
1,5 mm
2
(Green/Yellow wire = Earth ).
USE OF THE PRODUCT
ON/OFF MODEL

By means of the illuminated switch the towel warmer can be
switched on and off {ref. 1, pg. 17}.
IR SENSOR MODEL
 The product is fitted with a main on/off illuminated switch
positioned in the bottom side of its {ref. 3, pg. 18}. When the
switch is ON the internal control electronic is ready to
operate. By passing the hand (or a towel) over the IR sensor
the heating can be turned ON or OFF {ref. 2, pg. 18}. The led
on the side part of the appliance indicates the heating state
(red led ON

heating ON / red led OFF

heating OFF) {ref.
1, pg. 18}.