Holars AS H-TAG Скачать руководство пользователя

Страница: 2 / 15

CONTENTS

INTRODUCTION

………………………………… 2

INSTALLATION …………………………………

STANDALONE MODE

………………………… 6

CONTROLLER MODE

…………………………11

WIEGAND READER MODE

………………… 13

ADVANCE APPLICATION

………………….. 14

INTRODUCTION

The H-TAG is a single door multifunction standalone access controller or a Wiegand output reader.

It uses Atmel MCU assuring stable performance. The operation is very user-friendly, and low-

power

circuit makes it long service life.

The H-TAG supports 600 users, it supports multi access modes in either card access, PIN access,

Card + PIN access, or multi cards/PINsaccess. It has extra features including block enrollment,

interlocked, Wiegand 26~37 bits interface...etc.

Features

One relay, keyboard programmer

600 users

PIN length: 4~6 digits

Card type: 125KHz EM card, 125KHz HID card, 13.56MHz Mifare card

Wiegand 26~37 bits input & output

Can be used as Wiegand reader with LED & Buzzer output

Card block enrolment

Tri-colour LED status display

Pulse mode, Toggle mode

2 devices can be interlocked for 2 doors

Built in light dependent resistor (LDR) for anti tamper

Backlit keypad

Waterproof, conforms to IP66

Low temperature resistance(-40

℃

)

Содержание H-TAG
















Результаты поиска

Содержание H-TAG

Отзывы:

Похожие инструкции для H-TAG

Бренды по названию

Популярные бренды

Holars AS H-TAG, Руководство пользователя

Результаты поиска

Содержание H-TAG

Отзывы:

Похожие инструкции для H-TAG

Бренды по названию

Популярные бренды