Hofmann PMH-2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

background image

Relay 1:

240 VAC, 5 Amps max. Resistive load. 3 terminals

provide earth, neutral and switched active. 5A fuse

protects instrument and relay output.

Relay 2 / Alarm:

Potential free contacts.

Power:

240VAC 50Hz 7.5VA max. Hardwired with screw

terminals located under sub panel. 3 way terminal

providing 240VAC (A, N, E) located next to potential

free contacts allows for easy wiring of this terminal.

Housing:

Fully sealed construction with hinged clear acrylic

front cover. IP55 specifications.

Dimensions:

166mm x 160mm x 105mm.

PAGE 4

PMH-2 Instruction manual

«
...
2
3
4
5
6
...
»

Содержание PMH-2





























Отзывы:

Нет отзывов

Похожие инструкции для PMH-2

Бренд: U-Prox Страницы: 31

Бренд: Dantherm Страницы: 96

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 8

Бренд: Measurement Computing Страницы: 32

DIGITAL EPIC-2 DTM

Бренд: Westlock Страницы: 33

Бренд: Conel Страницы: 52

Бренд: Revox Страницы: 57

Бренд: Wittenstein Страницы: 52

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренд: Raypak Страницы: 2

Бренд: 4D systems Страницы: 6

Бренд: Phoenic Mecano Страницы: 5

I/A MicroNet MN-S Series

Бренд: t.a.c. Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды