ENGLISH
fra
N
ç
a
IS
DEUTSCH
4
esp
a
Ñ
ol
iMPortant - read this beFore running
PLease read aLL instructions and FaMiLiarize YourseLF with the Products and controL beFore
oPeration.
This product is not a toy. It is a high performance model product. It is important to familiarize yourself with the model, its
manual, and its construction before assembly and operation. Adult supervision is necessary
caUtion
To avoid serious personal injury and property damage, operate all remotely controlled models in a responsive manner as out-
lined below.
R/C car models can exceed speeds of 50km/h (31.07 mph), and cannot be stopped quickly.
❶
Never run R/C models on the street or highways, as it could cause or contribute to serious traffic accidents.
❷
Never run an R/C model near people or animals, nor use people or animals as obstacles when operation R/C vehicles.
❸
To avoid injury to persons or animals, and damage to property, never run a R/C model in a confined or crowed area.
❹
Running R/C models into furniture or other inanimate objects will cause damage to the objects and the R/C models.
caUtion DUrinG oPerations
When the R/C model is in operation, dot not touch any of its moving parts, such as drive shafts, wheels, as the rotating parts
can cause serious injury.
❶
The vehicle motor gets very hot during running and could cause burns if touched.
❷
Properly connect plugs. To prevent electrical shock and/or damage to the product resulting from a short-circuit; insulate
connections with heat shrink tubing or electrical tape. Before running vehicle, check that battery wiring and plugs are not so
loose as to drag on the ground. Properly secure cables using electrical tape or nylon tie-wraps.
❸
Stiff rotation of gears, shafts, joints and wheels can burn out the motor. It’s recommended to check proper joint and shaft
rotation by using one 1,5V dry cell during assembly of the model.
❹
R/C models will run out of control when either the receiver or transmitter battery voltage drops off. Stop the vehicle
immediately when the car starts to show down to prevent it from running out of control.
saFetY PrecaUtions
Follow the outlined rules for safe radio control operation.
Avoid running the car in crowed area and near small children.
Avoid running in standing water and rain. If R/C unit, motor, or battery get wet, clean and dry throughly in a dry shaded area.
R/C operating procedures
❶
Make sure the transmitter controls and trims are in neutral. Switch on transmitter.
❷
Switch on receiver.
❸
Inspect operation using transmitter before running.
❹
Adjust steering servo and trim so that the model runs straight with transmitter in neutral.
❺
Reverse sequence to shut down after running.
❻
Make sure to disconnect/remove all batteries.
❼
Completely remove sand, mud, dirt etc
❽
Store the car and batteries separately when not in use
settinG UP tHe moDeL
To greatly enhance the overall performance of your car, it’s necessary to tune the vehicle to the track (and its surface
conditions) on which you will be racing. Make adjustments referring to the instruction manual, keeping in mind that “balance” is
the key word.
❶
tires
Tires have a great influence on the performance of your car, and are normally the first components tuned. Select the right tires
for the track you are racing on.
❷
toe-in and toe-out
Adjusting the car toe-in a little, by pointing the wheel inwards, provides the car with good straight running and moderate
steering characteristics. Toe-out, which point the wheels outwards, gives sharp and crisp steering. Take care not to overdo.
❸
camber angle
While taking the corners, the car is forced to go outwards, causing instability. The area of contact on each tire is determined
by the camber angle, and therefore the traction of the tires can be made greater or lesser by adjustment of camber angle. To
increase traction during cornering, adjust camber angle negative, and reduce traction, adjust for positive camber.
❹
Ground clearance and suspension drop
Ground clearance and/or rebound stroke has a great effect on stability during cornering, acceleration, and braking. Ground
clearance can be adjusted by altering damper spring tension and stiffness.
❺
Gear ratio
Proper gear ratio should be determined by the available output power of the engine; type of battery; track condition and layout
It should be also noted that running the car on a good grip surface suggests use of clutch bell 1 teeth smaller, in order to
effectively use all of the available engine power.
