background image

1

HZ1696-E

Assembling manual

PJR-series Wide beam/Triple type

Carport

Thank you very much for choosing our company's products.

Please be sure to thoroughly read these instructions for assembly in order to properly and smoothly assemble or attach this product.

Notices are the important contents for securing the performance of the products, the function, the strength and safety. Please be 

sure to keep the notices when installing.

Construction shall be implemented by professionals. Problems may occur if the product is installed by someone without the 

proper knowledge.

Precautions during installation

□T

he carport is a simple garage. Do not change or remodel it for storage, recreational or residential purposes.

The snow accumulation strength is 600N/m

2

 (61.2kg/m

2

) which corresponds to 20cm of fresh snowfall (specific weight 0.3). Do 

not install in heavy snow area. 

Do not install it in the place where snow slides down from the building roof directly. There is a possibility that products are 

damaged by snow falling.

When installing it besides concrete wall, etc., keep the enough clearance between the product and the wall due to not clash 

each other during strong wind. 

Do not install it in the place where the strong wind blows up the roof.

When installing it, recommending to installing its front frame face to the building due to reduce the wind effect.

Positioning the posts so that they do not affect underground objects (water supply, drain pipes, etc.).

When moving the posts, please follow the company specifications.

Install it so that the exhaust of hot-water supply, heating and/or the car do not hit directly to the products and do not retain 

around products. There is a possibility that the surface abnormality occurs as the coating film stripping.

Name of parts

Please be sure to return the instruction manual in its original package to the owner after explaining product operation 

procedures, maintenance and inspection methods.

Notice

Gutter

Roof panel

Post

Side frame

Roof retainer

Main frame

Roof rafter

Beam

enough space

enough space

concrete wall etc

Содержание PJR Series

























Отзывы: