manualshive.com logo in svg

HobbyKing Gulfstream G500 ARF, Инструкция по сборке

Поделиться
Скачать
HobbyKing Gulfstream G500 ARF Скачать руководство пользователя страница 3

 

 

Step 3: Installing the servos 

Locate the seven servo door covers and cut the covering film away from each to expose the hole 
through which the servo horn will pass (2x aileron, 2x flap, 2x elevator and 1x rudder). 

 

Next, attach servos to the underside of each of these. This may be done using glue, but ideally you 
should attach by gluing two small blocks (provided) to the underside of these covers and screwing 
the  servos  to  these  (see  below).  Don’t  forget  to  center  your  servos  before  this  step;  this  makes 
things easier later on! 

 

Now, attach servo extension wires to the aileron, flap and rudder servos. Use the following 
lengths: 

!

 

Aileron servos (those attached to the smaller gray covers):  60cm 

!

 

Flap servos (those attached to the larger gray covers): 50cm 

!

 

Rudder servo (should be obvious): 1m 

Leave the elevator servos alone for the moment. 
 
These servos may now be installed in their allocated places. For the main wing servos, feed the 
wire through the wing to the exit provided. For the rudder servo, feed the wire through the body of 

Содержание Gulfstream G500 ARF



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды