background image

4

Battery Precautions

•  Do not use the battery if it is damaged or 

deformed.

•  Do not solder the motor leads directly to the 

battery.

•  Do not reverse charge or over discharge the 

battery.

•  Do not reverse charge or connect the battery in 

reverse to the speed control.

•  Do not connect the battery to the ordinary charger 

socket or car cigarette jack.

•  Do not use the battery for unspecified equipment.

•  Do not touch the leaking battery directly. Wash 

your skin or clothes with water if they come in 

contact with a damaged battery.

•  Do not mix the Li-Po battery with other un-

chargeable battery.

•  Do not continue charging the battery over the 

prescribed time.

•  Do not put the battery into a microwave oven or 

high-pressure container.

•  Do not use an abnormal or damaged battery.

•  Do not use or store a battery under the sunlight.

•  Do not use the battery near any sources that 

generate static electricity (over 64V)

•  Do not charge the battery when the environmental 

temperature is under 32 degrees or over 130 

degrees.

•  If you find the battery leaking smelling or 

abnormal, stop using it.

•  Keep the battery away from children.

•  Use the specified charger and observe charging 

requirement provided by the battery manufacturer.

•  Parental supervision is required when charging or 

operation is done by minors.

•  Never charge the battery at a rate greater than 

specified by the battery manufacturer.

•  Never discharge the battery at more than 25C and 

never take the voltage lower than 12V as this will 

damage the battery.

•  For full flight time it is recommended to cycle the 

battery a minimum of three cycles before use in 

your model.

•  Never charge the battery on a carpet floor as this 

can cause a fire.

Mixing Epoxy

When mixing epoxy, make sure to use equal amounts 

of Part A and Part B. Mix the epoxy thoroughly. You 

will have about 3 minutes before the epoxy begins to 

cure after mixing so work quickly. Do not mix epoxy 

until you fully understand the assembly procedure.

Содержание SU-34 Fullback

















Отзывы: