Hobart VPU 100 Скачать руководство пользователя страница 8

Страница: 8 / 8

Trouble shooting

Fault

Cause

Correction

machine does not start

uncorrect position of feed head

make sure the feed head is locked
correctly

pusher plate not correctly

lower pusher plate into feed head

positioned

site fusing or circuit breaker

check fusing / circuit breaker

blown

(wall box)

machine stops during operation

pusher plate not correctly

lower pusher plate into into feed head

and cannot be re-started

positioned

site fusing or circuit breaker

check fusing / circuit breaker

blown

(wall box)

motor overload protection

let overload protection cool, the

has cut machine off

machine may be re-started after

(i.e. when cutting hard product

some minutes

for a long time without stopping)

low output or

wrong disc in use

see chapter 3 (cutting tool guide)

poor cutting results

disc damaged

check disc (sharpness)

too strong feed pressure

a slight feeding pressure leads to

of pusher

the best cutting results for most
products

As continued product improvement is a policy of HOBART, specifications are subject to change without notice.

Printed in Germany

AG-20264-B-02-93-TD

Содержание VPU 100









Результаты поиска

Содержание VPU 100

Отзывы:

Похожие инструкции для VPU 100

Бренды по названию

Популярные бренды

Hobart VPU 100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VPU 100

Отзывы:

Похожие инструкции для VPU 100

Бренды по названию

Популярные бренды