HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 53

Страница: 53 / 89

8 Startup/shutdown of a mzr-pump

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

Nature of the delivered liquid

Flushing time [min]

Suitable flushing liquid

Oils, fats, plastifierss

15-20

isopropanol, ethanol, acetone,
benzine/petroleum ether

Solvents (polar + nonpolar)

5-10

isopropanol, ethanol

Other organic liquids

10-15

isopropanol , ethanol

Refrigerating and cooling agents

15-20

isopropanol, ethanol

Neutral water/y solutions

20-25

isopropanol, ethanol

Basic solutions

25-30

DI-water (deionized water)

Organic acids

30-40

isopropanol, ethanol

Weak mineral acids

25-30

DI- water

Strong mineral acids

35-45

DI- water

Strong oxidizing liquids

35-45

DI- water

Paints, varnishes, adhesives

50-60

not specified - for further information
please contact HNP Mikrosysteme.

table 28

Selection of the flushing liquid (solvent) and the duration of the flushing procedure depending on the
delivered liquid.

Warning

Please make sure that the pump components and particularly O-rings and

sealing are resistant to the employed flushing liquid (see table 29).

Shaft sealing

O-ring material

Flushing liquid

PTFE (Teflon

graphite-

reinforced

UHMWPE

FPM

(Viton

)

EPDM

FFPM

acetone

benzene

benzyl alcohol

butanol

dimethyl sulfoxide (DMSO)

ethanol

isopropanol

methanol

methylethylketone (MEK)

styrene

toluene

water

xylene

benzine/petroleum ether

oil / fine mechanics oil

Legend:

0 ... good suitability 1 ... suitability 2 ... conditional suitability 3 ... labile - ... not specified

table 29

Resistance of the sealing materials depending on the flushing liquid (solvent)

8.4

Shutdown of the micro annular gear pump

In order to shut down a mzr-pump the following steps should be followed:

−

Flush the pump with a filtered and particle-free flushing liquid (solvent) as

described in the chapter 8.3.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды