manualshive.com logo in svg

HME WIRELESS 6000, Руководство по эксплуатации

Поделиться
Скачать
HME WIRELESS 6000 Скачать руководство пользователя страница 19

 17 

VII. OPTIONAL 

EQUIPMENT 

 

Equipment 

Model Number 

COMMUNICATOR

®

 COM6000BP 

Battery for Communicator 

BAT40 

Headset Earmuff 

No model number 

Ceiling Speaker 

MM100 

Ultrasonic Vehicle Detector 

DU3 

Vehicle Detector Board 

VDB101 

Vehicle Detector Loop (underground) 

VDL100 

Message Repeater 

MR300 

Low-Profile Speaker 

SP2500LP 

Microphone DM3 

Mode Switch (dual lane) 

MS1000 

Switcher Circuit Board 

No model number 

Remote Record Switch 

No model number 

Remote Antenna Kit 

No model number 

Remote Speed Team Switch 

SW2 

VIII. FCC NOTICE 

This device complies with Part 15 of the FCC rules.  Operation is subject to the following 
two conditions:  (1) This device may not cause harmful interference, and (2) This device 
must accept any interference received, including interference that may cause undesired 
operation. 

NOTE:

  This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to Part 15 of the FCC rules.  These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment.  This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communication.  Operation of this equipment in a residential 
area is likely to cause harmful interference, in which case the user will be required to 
correct the interference at his own expense. 

Changes or modifications not expressly approved by HM Electronics, Inc. could void the 
users authority to operate this equipment. 
 
 

The antenna(s) used for the base transmitter must be installed to provide a separation distance of at 
least 20 cm from all persons and must not be co-located or operating in conjunction with any other 
antenna or transmitter. 
This device has been designed to operate with an antenna having a maximum gain of 2dBi.  Antenna 
having a higher gain is strictly prohibited per regulations of Industry Canada.  The required antenna 
impedance is 50 ohms. 
The term “IC:” before the certification/registration number only signifies that the Industry Canada 
technical specifications were met. 

 
 
 
 
 

This product operates in the 2400 to 2483.5 MHz frequency range.  The use of this frequency range is 
not yet harmonized between all countries.  Some countries may restrict the use of a portion of this 
band or impose other restriction relating to power level or use.  You should contact your Spectrum 
authority to determine possible restrictions.

 

Содержание WIRELESS 6000




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды