background image

 

Care and replacement of glass: 

           Never strike the glass or slam door shut as such abuse can damage the glass and cause it to 
fail. Never operate your appliance with broken glass. Never attempt to clean glass when hot. Never 
clean glass with harsh abrasives. Replace glass only with ROBAX CERAMIC glass 254, 5mm x 
9”(228.6mm) x 15 9/16”(395.2mm), 354 5mm x 9”(228.6mm) x 17 7/16”(443mm)) available from your 
Hitzer dealer. Use of any other type of glass can cause glass to fail creating a fire hazard.  
           Should you be required to replace the glass first remove door from your stove and lay face 
down on a smooth solid surface. You will want to pad the surface especially if you have the optional 
plated door so as not to scratch the finish. Remove and save the glass retainers and screws. Carefully 
remove all broken glass and sealing gasket material. Install new glass using new sealing gasket 
material and reinstall all glass retainers and screws. 
 

End of season maintenance: 

  Moisture is your enemy. Summertime moisture and high humidity can be absorbed by dust and fly 
ash and cause rust and corrosion. A complete cleaning of the stove and venting system will help 
reduce this. Brush down all fly ash from the interior of the stove. Then you should vacuum out the fly 
ash from inside the stove including ledges and corners. Check outside painted surface of stove. If 
surface rust or blemishes are present lightly rub with fine steel wool to remove. You can then touch up 
the paint with high temperature stove paint available at your Hitzer dealer. 
  Next clean the venting system. Disconnect the chimney connector pipe and clean all fly ash from it 
especially elbows and horizontal runs.  It is not necessary to reinstall this pipe till you are ready to use 
the stove again in the fall. Have the chimney inspected and cleaned if necessary.  
   At the beginning of each heating season this appliance, the connector pipe, and chimney should be 
inspected to see that they are clear and in good working condition. 
    
 For  more  information  in  the  proper  installation  and  operation  of  your  quality  HITZER  heater  contact 
your local HITZER dealer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 254















Отзывы: