background image

: The symbol refers to a hazard which can result in severe personal injury or death.
: The symbol refers to a hazard or an unsafe practice which may result in severe personal injury 

  

or death. 

: The symbol refers to a hazard or an unsafe practice which may result in personal injury, 

  

  

product or property damage. 

: It refers to the remarks and instruction to the operation, maintenance, and service.

DANGER

WARNING

CAUTION

NOTE

Alert Symbols

This air conditioner should be installed properly by qualified personnel in accordance with the installation 
 instructions provided with the unit. 
This product is a comfort air conditioner and must not be used as special environments appliance, such 
 as industrial air conditioner, base station air conditioner, computer air conditioner, etc.
Before installation, check if the voltage of the power supply at installation site is the same as the voltage 
shown on the nameplate. 

You must not carry on any transformation to this product, otherwise, it may cause 
water leakage, breakdown, short-circuit, electric shock, fire, and so on.
Piping, welding and other such works should be carried out far away from the 
flammable explosive material vessels, including the air conditioner refrigerant, to 
guarantee the security of the site.
To protect the air conditioner from heavy corrosion, avoid installing the outdoor unit 
where sea water can splash directly onto it or in sulphurous air near a spa. Do not 
install the air conditioner where excessively high heat-generating objects are placed. 

DANGER

WARNING

If the supply cord is damaged, it must be replaced by the factory or its service department 
in case of danger.
The place where this product is installed must have the reliable electrical grounding facility 
and protection. Please do not connect the grounding of this product to various kinds 
of air-feeding ducts, drain piping, lightning protection facility as well as other piping lines to 
avoid receiving an electric shock and damages caused by other factors.
Wiring must be done by a qualified electrician. All the wiring must comply with the local 
electrical codes. 
Consider the capacity of the electric current of your electrical meter and socket before 
installation. 
The power wire where this product is installed is supposed to have the independent 
leakage protective device and the electric current over-load protection device which are 
provided for this product.

This appliance can be used by children aged from 8 years and above and persons with 
reduced physical, sensory or mental capabilities or lack of experience and knowledge if 
they have been given supervision or instruction concerning use of the appliance in a safe 
way and understand the hazards involved.

 

Children shall not play with the appliance. 

Cleaning and user maintenance shall not be made by children without supervision.

Means for disconnection, which can provide full disconnection in all poles, must be 
incorporated in the fixed wiring in accordance with the wiring rules .

1

Caution Statements

California Residents Only-
Cancer and Reproductive Harm 
www.P65Warnings.ca.gov  

WARNING

Содержание RPIL-1.0PNN1DH





















Отзывы: