Hitachi RAC-50FX8, Руководство по обслуживанию

Страница: 13 / 190

– 11 –
SILENT LOW MED HI
AUT
O
HEA
T
DEHUMIDIFY COOL FA
N
F
AN SPEED
SLEEPING ST
OP
(CANCEL)
ST
ART
(RESER
VE)
ST
AR
T/ST
OP
TIME TIMER SET TIMER SELECT
OR
ON TIMER OFF TIMER
AUT
O SWING
EXTENDED AIRFLOW
NAMES AND FUNCTIONS OF EACH P
A
R
T
REMOTE CONTROLLER
This controls the operation of the indoor unit.
The range of control is about 7 meters. If indoor lighting is
controlled electronically
, the range of control may be shorter
.
be controlled from the remote controller
.
Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission capability
.
After new batteries are inserted into the remote controller
, the unit will initially require approximately 10
seconds to respond to commands and operate.
Precautions for Use
Do not put the remote controller in the following places.
In direct sunlight. In the vicinity of a heater
.
it from water
.
Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch of
f and on or unplug the power cord and plug it in again).
This is to protect the device and does not indicate a failure. If you press the FUNCTION selector button during operation, the device may stop for about 3 minutes for protection. Signal emitting window/transmission sign The transmission sign blinks when a signal is sent. Display This indicates the room temperature selected, current time, timer status, function and intensity of circulation selected. ST
ART/ST
OP button
Press this button to start operation. Press it again to stop operation. SLEEP button Use this button to set the sleep timer
.
TEMPERA
TURE buttons
Use these buttons to raise or lower the temperature setting. (Keep pressed, and the value will change more quickly
.)
TIME button Use this button to set and check the time. RESET buttons FUNCTION selector Use this button to select the operating mode. Every time you press it, the mode will change from
(AUT
O) to
(HEA
T) to
(DEHUMIDIFY) to
(COOL)
and to
(F
AN) cyclically
.
F
AN SPEED selector
This determines the fan speed. Every time you press this button, the intensity of circulation will change from
(AUT
O) to
(HI) to
(MED) to
(LOW)
to
(SILENT). (This button allows selecting the optimal or preferred fan speed
for each operation mode.) AUT
O SWING button
EXTENDED AIRFLOW
button
TIMER control Use these buttons to set the timer
.
OFF-TIMER button
Select the turn OFF time.
ON-TIMER button
Select the turn ON time.
RESER
VE button
Ti
me setting reservation.
CANCEL button
Cancel time reservation.
– 6 –
•
This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can
• •
•
• •
•
Handle the remote controller carefully
• •
Controls the angle of the horizontal air deflector Pushes air out further for an extended airflow
– 7 –
ENGLISH
V
ARIOUS FUNCTIONS
Auto Restart Control
AUTOMATIC OPERATION
The device will automatically determine the mode of operation, HEA
T
, COOL, or DEHUMIDIFY
, depending
on the initial room temperature.
The selected mode of operation will change when the room temperature
varies. However
, the mode of operation will not change when indoor unit connected to multi type outdoor
unit.
Press the
(F
AN SPEED) button,
AUT
O, LOW and SILENT are available.
Press the
(ST
A
R
T
/ST
OP) button.
Operation starts with a beep. Press the button again to stop operation.
As the settings are stored in memory in the remote controller
, you only have
to press the
(ST
A
R
T
/ST
OP) button next time.
Y
ou can raise or lower the temperature setting as necessary by maximum
of 3
°
C.
Press the temperature button and the temperature setting will change by 1
°
C each time.
•
The preset temperature and the actual room temperature may vary somewhat depending on conditions.
1
START
STOP
Press the FUNCTION selector so that the display indicates
the
(AUT
O) mode of operation.
•W
hen
AUT
O has been selected, the device will automatically
determine the mode of operation, HEA
T
, COOL, or DEHUMIDIFY
,
depending on the current room temperature.
•
If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation mode and airflow direction. (As the operation is not stopped by remote controller
.)
•
If you intend not to continue the operation when the power is resumed, switch of
f the power supply
.
When you switch on the circuit breaker
, the operation will be automatically restarted with previous
operation mode and airflow direction. Note:
1.
If you do not require
Auto Restart Control, please consult your sales agent.
2.
Auto Restart Control is not available when
T
imer or Sleep
T
imer mode is set.