manualshive.com logo in svg

Hitachi RAC-112SQB, Руководство по установке

Поделиться
Скачать
Hitachi RAC-112SQB Скачать руководство пользователя страница 10

10 

(3) Pipe removal direction 

 

 
 

※

Size cover flash after removing it. Wrap wires and pipes with the insulation sheet (prepare on-site). 

 

●

  Front and right piping 

●

 Bottom 

piping 

●

 Rear 

piping  

Remove the rear piping cap next 
to the bottom cover and remove 
the cover as shown in the shaded 
part 

  in the diagram below.

 

 

1)

 

When using rubber stoppers and electrical hoses, check the size of the above mentioned seams before removing the 
cover in the shaded part 

. 

2)

 

Before removing pipes installed in the front and on the right, leave adequate space for removing wires. For example, 
when removing pipes installed in the rear and on the right, remove pipes from the upper part of the seams (A). Make 
sure pipes and wires inside the unit do not interfere with each other. 

3)

 

Bend the pipe for the turns with a pipe bender. 

4)

 

To prevent burrs from damaging pipes and wires, wrap pipes and wires with insulation sheets (prepare on-site). 

5)

 

To prevent rainwater from entering the unit, put back the pipe cover afterwards. Wrap pipes with insulation sheets 
(prepare on-site) before penetrating pipes through the cap hole to ensure it is seamless. Make sure that there is 
adequate space for putting back the pipe cover. 

 

 

 

Panel removal 
direction 

Rear piping

Pipe cover

Front piping

Right piping

Bottom piping (cover) 

y

 

As shown in the left diagram, 
pipes can be installed in four 
locations. Remove the cover 
where the pipe is installed and 
install the pipe through the 
hole. Break the cover with a 
screwdriver and remove it. 
Break the bottom cover with a 
small hammer. 

Break the cover 
with a screwdriver 
and remove it.

 

Break the cover   
with a screwdriver 
and remove it. 

Break the cover 
with a screw driver 
and remove it.

 

Pipe cover

Upper right 

rear cover.

Removal of pipes 

installed in front. 

Wire

Gas pipe 

Cover 

Fluid pipe 

Stand

Panel Cover 
(4 hooks) 

① 

Press the panel cover with 
one hand and remove the 
screw on the left. 

② 

Push the cover downward 
and move to the right to 
remove it. 

Lower right 

rear cover.

Removal of pipes 

installed on the right 

Guidelines for Opening Panel 

Cover 

Upper Right Rear cover

Lower Right Rear cover

Содержание RAC-112SQB





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды