49
（繼續）
（Continue）
故障了嗎﹖
TROUBLESHOOTING
When in trouble
發生問題時
故障了嗎?
（繼續）
Troubleshooting (continue)
( )
28
頁
( )
12
頁
冰塊是否放太久了？
有無頻繁開啟箱門．打開箱門的時間
過久？
有無停電？
冰塊變圓．
變小．黏著
在一起
突起
檢查項目
Please check
Is there a blackout?
Has the ice been left stored for a long time?
Has the door been opened frequently
or left open for a long time?
Ice cube are
round, small,
joined
together
框不能拉出來
手把拉下來了吧？
[ 製冰選擇 ] 顯示燈亮著嗎？
按下手把後將框拉出來。
在自動製冰時不能拉出來。要將框拉出來，
可以先按下 [ 製冰停止 ] 按鍵，顯示燈會閃爍
約
20
秒鐘，待顯示燈熄滅後才能拉出。
冰塊的大小
不變
製冰設定剛結束時，冰塊的大小是不會馬上變的。
給水槽內的水量變少的話，就不
能製出大塊的冰。
往給水槽內注水。
是否沒有調整好平行調整。
沒有調整好平行整的調話，就製不出平均
大小的冰塊。
冰塊融化了。
冷凍室不夠冷的時候就不能結冰。
冷凍室不夠冷的時候就不能結冰。
是否在製冰盒內有水的情況下裝置的？
有時候當給水槽內沒水了，或者注水後剛開始做好的冰塊也會發生相互連結或變小。
冰塊粘連時，請用附屬的冰鏟加以分開。
要做出一樣大小的冰塊時後，製冰盒有這樣的水路設計，這樣的水路設計會使做出
來的冰塊前端會產生突起狀。
When the water in the water supply container runs out and has just been filled, the first ice
to come out of the machine may be joined together or small.
If ices cubes are joined, separate them with the provided ice scoop.
Water passage is made on the ice tray to make ice cubes of uniform size.
This water passage makes projection at the end of ice cube.
冰塊變圓．
變小．黏著
在一起
Ice cube are
round, small,
joined
together
一定要在製冰盒內是空的情況下裝置。
The frame
cannot be
pulled out
Is the lever pulled down?
Pg. 42
Pull down the lever before pulling out the frame.
Is the "Large ice cube making" button
light on?
Size of ice
cube cannot
be changed
Size of ice cube may not change immediately after large ice cube making setting is changed.
Projection
“Larger” size of ice may not be
made if the water level in the water
supply container is low.
Pg. 28
Pg. 12
Add water in the water supply container.
Is the refrigerator installed on the
flat floor?
If the refrigerator leans to one side, ice cube size
cannot be uniform. Adjust the levelling.
This is because ice was sublimated.
Ice cannot be made until the freezer
compartment is sufficiently cooled.
Ice cannot be made until the freezer
compartment is sufficiently cooled.
Was the ice tray set with water in it?
Make sure to empty the ice tray before setting
it in the ice maker.
( )
42
頁
( )
31
頁
Pg. 31
It cannot be pulled out during automatic ice
making operation. To pull it out, stop ice making
and if the light is flashing, wait for
approximately 20 seconds until the light turns
off.
解決方法
What to do
問題
Problem
R-X6000H_A4.indd 49
R-X6000H_A4.indd 49
12/5/07 9:54:29 AM
12/5/07 9:54:29 AM
