background image

OPERATION & INSTALLATION MANUAL FOR PC-RLH8/10 

1

ENGLISH 

1 SAFETY 

SUMMARY 

Õ

DANGER

:

DO NOT pour water into the remote control switch (hereafter called "controller"). This product 
is equipped with electrical parts. 
If poured, it will cause a serious electrical shock. 

Ô

WARNING:

DO NOT perform installation work and electrical wiring connection by yourself. Contact your 
distributor or dealer of HITACHI and ask them for installation work and electrical wiring by 
service person. 

CAUTION:

DO NOT install the indoor unit, outdoor unit, at such places as: 
-   Where there is oil vapor and the oil is dispersed. 
-   Where the hot springs are near (in a sulfuric environment). 
-   Where generation, flowing, staying  or leaking of flammable gas is detected 
-   Where the sea is near ( in the salty, acid or alkaline environment). 
-    DO NOT install the indoor unit, outdoor unit, within approximately 3 meters from strong 

electromagnetic wave radiators such as medical equipment.  

-   In case that there is electric noise at the power source for the indoor unit, provide a noise 

filter

.

-  Do not  turn ON the power source, unless the preparation for test running is completed. 
-  Read this manual carefully before installation work for correct performance. 

2  BEFORE INSTALLATION AND OPERATION 

■ 

The packing contains the following parts.  Check the contents and the number of the parts. 

Model

Name

Q'ty 

Remark

Receiver Kit 

With Connection Wire 

Connecting Cable 

 

With Connection Wire 

Band

For Fixing Cable 

PC-RLH8

Cover 

 

For Protection of Connecting Cable 

Receiver Kit 

With Connection cable 

Band

For Fixing Cable 

PC-RLH10

Insolation 

 

For Protection Cable 

Содержание PC-RLH10











Отзывы: