Hitachi DS 12DVC, Инструкция по эксплуатации

Страница: 11 / 16

10
c) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk
of injury and fi re.
d) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects that can make a connection
from one terminal to another.
Shorting the battery terminals together may cause
burns or a fi re.
e) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, fl ush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a quali fi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in fi rm persons away.
When not in use, tools should be stored out of reach of
children and in fi rm persons.
PRECAUTIONS FOR CORDLESS DRIVER DRILL
1 . Always charge the battery at a temperature of 10°C –
40°C . A temperature of less than 10°C will result in over
charging which is dangerous . The battery cannot be
charged at a temperature higher than 40°C .
The most suitable temperature for charging is that of
20°C – 25°C .
2 . When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery .
Do not charge more than two batteries consecutively .
3 . Do not allow foreign matter to enter the hole for connecting
the rechargeable battery .
4 . Never disassemble the rechargeable battery and
charger .
5 . Never short-circuit the rechargeable battery . Short-
circuiting the battery will cause a great electric current
and overheat . It results in burn or damage to the battery .
6 . Do not dispose of the battery in fi re .
If the battery is burnt, it may explode .
7 . When drilling in wall, fl oor or ceiling, check for buried
electric power cord, etc .
8 . Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use . Do not dispose of the exhausted
battery .
9 . Using an exhausted battery will damage the charger .
10 . Do not insert object into the air ventilation slots of the
charger .
Inserting metal objects or in fl ammables into the charger
air ventilation slots will result in electrical shock hazard or
damaged charger .
11 . Do not move the charger by pulling it by the cord . Doing
so may lead to damage .
12 . When mounting a bit into the keyless chuck, tighten the
sleeve adequately . If the sleeve is not tight, the bit may
slip or fall out, causing injury .
SPECIFICATIONS
POWER TOOL
Model DS9DVC DS12DVC
No-load speed (Low/High) 0 – 260 / 0 – 1150 /min 0 – 350 / 0 – 1400 /min
Capacity
Drilling
Wood
(Thickness 18 mm)
21 mm 24 mm
Metal
(Thickness 1 . 6 mm)
Steel: 10 mm
Aluminum: 12 mm
Steel: 12 mm
Aluminum: 15 mm
Driving
Machine screw 6 mm 6 mm
Wood screw
5 . 8 mm (diameter) × 45 mm (length)
(Requires a pilot hole)
5 . 8 mm (diameter) × 45 mm (length)
(Requires a pilot hole)
Rechargeable battery BCC912: Ni-Cd 9 . 6 V (1 . 2 Ah 8 cells) BCC1212: Ni-Cd 12 V (1 . 2 Ah 10 cells)
Weight 1 . 2 kg 1 . 3 kg
CHARGER
Model UC18YK UC9SF UC12SF
Charging voltage 7 . 2 – 18 V 9 . 6 V 12 V
Weight 0 . 35 kg 0 . 6 kg 0 . 6 kg
000Book̲DS9DVC̲Ch.indb 10 000Book̲DS9DVC̲Ch.indb 10 2010/06/18 9:46:27 2010/06/18 9:46:27