English
15
11. Using the hook
CAUTION:
䡬
When using the hook, pay sufficient attention so
that the main equipment does not fall. If the tool
falls, there is a risk of accident.
䡬
Do not attach the tip tool except phillips bit to the
tool main unit when carrying the tool main unit with
the hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side and
the angle can be adjusted in 5 steps between 0° and
80°.
(1) Operating the hook
(a) Pull out the hook toward you in the direction
of arrow (A) and turn in the direction of arrow
(B) (
Fig. 12
).
(b) The angle can be adjusted in 5 steps (0°, 20°,
40°, 60°, 80°).
Adjust the angle of the hook to the desired
position for use.
(2) Switching the hook position
CAUTION:
Incomplete installation of the hook may result in
bodily injury when used.
(a) Securely hold the main unit and remove the
screw using a slotted head screwdriver or a coin
(
Fig. 13
).
(b) Remove the hook and spring (
Fig. 14
).
(c) Install the hook and spring on the other side and
securely fasten with screw (
Fig. 15
).
NOTE:
Pay attention to the spring orientation. Install the
spring with larger diameter away from you (
Fig. 15
).
(3) Using the bit holder (Hook with bit holder)
䡬
Installing the bit
Slide the bit from the side in the direction of
Fig. 16
, and then insert firmly until the groove
on the bit locks in the protruded section of the
hook.
䡬
Removing the bit
Securely hold the main unit and pull out the bit
by holding the tip with your thumb (
Fig. 17
).
CAUTION:
䡬
The bit may come loose from the hook and cause
bodily injury when reversing the direction of the
bit as shown in
Fig. 16
or when using the driver
with the bit stored incomplete.
䡬
Only Hitachi STANDARD ACCESSORIES phillips bit
(No. 2
×
55L; Code No. 318236) may be used. Do
not use other bits since they may come loose.
(4) Using as an auxiliary light (Hook with light)
(a) Press the switch to turn off the light.
If forgotten, the light will turn off automatically
after 15 minutes.
(b) The direction of the light can be adjusted within
the range of hook positions 1 - 5 (
Fig. 18
).
䡬
Lighting time
AAAA manganese batteries: approx. 15 hrs.
AAAA alkali batteries: approx. 30 hrs.
CAUTION:
Do not look directly into the light.
Such actions could result in eye injury.
(5) Replacing the batteries
(a) Loosen the hook screw with a phillips-head
screwdriver (No. 1) (
Fig. 19
).
Remove the hook cover by pushing in the
direction of the arrow (
Fig. 20
).
(b) Remove the old batteries and insert the new
batteries. Align with the hook indications and
position the plus (+) and minus (–) terminals
correctly (
Fig. 21
).
(c) Align the indentation in the hook main body
with the protuberance of the hook cover, press
the hook cover in the direction opposite to that
of the arrow shown in
Fig. 20
and then tighten
the screw.
Use commercially available AAAA batteries
(1.5 V).
NOTE:
Do not tighten the screw excessively. Such action
could strip the screw threads.
CAUTION:
䡬
Failure to observe the following can result in battery
leakage, rust or malfunction.
Position the plus (+) and minus (–) terminals
correctly.
Replace both batteries at the same time. Do not mix
old and new batteries.
Remove exhausted batteries from the hook
immediately.
䡬
Do not discard batteries together with normal trash
and do not throw batteries into fire.
䡬
Store batteries out of the reach of children.
䡬
Use batteries correctly in accordance with the battery
specifications and indications.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or
replace the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Cleaning on the outside
When the driver drill is stained, wipe with a soft
dry cloth or a cloth moistened with soapy water.
Do not use chloric solvents, gasoline or paint thinner,
for they melt plastics.
4. Storage
Store the driver drill in a place in which the tempera
ture is less than 40°C and out of reach of children.
5. Service parts list
CAUTION:
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
01Eng_DS9DVB2_EE
08/4/16, 17:32
15
