Hitachi CP-S245 Скачать руководство пользователя

Страница: 36 / 108

Multifunctional settings

Item

Description

START UP

Using the buttons ▲/▼ switches the mode for the start-up screen.

The start-up screen is a screen displayed when no signal or an

unsuitable signal is detected.

MyScreen



ORIGINAL



TURN OFF

MyScreen is a screen you can register as a desired screen.The

ORIGINAL screen is the existing standard screen. When TURN

OFF is selected, the BLACK screen is used.
• To avoid remaining as an afterimage, the MyScreen and the

ORIGINAL screens will change to the BLANK screen after several

minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it

will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen

below

. For

the BLANK screen, please refer to the BLANK item (



MyScreen

This item functions for capturing the MyScreen of the blank screen

and the start-up screen. Please execute displaying the input

including the picture you want to capture.
1. Selecting this item displays a dialog titled “MyScreen”. It will ask

you if you start capturing the picture from the current screen.

Please wait for the target picture to be displayed, and press

the ENTER button on the remote control when the picture is

displayed. The picture will freeze and the frame for capturing

appears.

To stop performing, press the RESET or ESC button on the

remote control.

2. Using the buttons ◄/►/▲/▼ adjusts the frame position. Please

move the frame to the position of the picture which you want to

use.

The frame may not be able to be moved for some input signals.

To start registration, press the ENTER button on the remote

control.

To restore the screen and return to the previous dialog, press the

RESET or ESC button on the remote control.

Registration takes several minutes. When the registration is

completed, the registered screen and the message “MyScreen

registration is ﬁnished.” are displayed for several seconds. If the

registration failed, the message “A capturing error has occurred.

Please try again.” is displayed.

MyScreen Lock

Using the buttons ▲/▼ turns on/off the MyScreen lock function.

TURN ON



TURN OFF

When the TURN ON is selected, the item MyScreen is locked. Use

this function for protecting the current MyScreen.

SCREEN Menu (continued)

Содержание CP-S245













































































































Результаты поиска

Содержание CP-S245

Отзывы:

Похожие инструкции для CP-S245

Бренды по названию

Популярные бренды

Hitachi CP-S245, Руководство пользователя

Результаты поиска

Содержание CP-S245

Отзывы:

Похожие инструкции для CP-S245

Бренды по названию

Популярные бренды