manualshive.com logo in svg

Hitachi C 12FDH, Технические данные и руководство по обслуживанию, Страница: 53 / 76

Поделиться
Скачать
Hitachi C 12FDH Скачать руководство пользователя страница 53

--- 49 ---

a  Ink line is not right

angle.

b  Laser marker accuracy

is not adjusted
properly.

c  Product accuracy is

not good.

------

0.2/100

(Figs. 70 and 71)

• Make a correct ink line again.

• Readjust the accuracy of the

laser marker.  (Refer to "11-9.
Adjustment of Laser Marker
Accuracy".)

• Readjust the accuracy of the

product and the laser marker.

Item

Phenomenon

Cause

Factory

standard

Inspection, repair or

adjustment

8

Laser line does not
match the ink line.

Fig. 70

Fig. 71

a  Laser marker is

horizontally deviated
from the saw blade.

b  Laser marker accuracy

is not adjusted
properly.

------

------

• Adjust the position of the laser

line.  (Refer to "8-1. Position
Adjustment of Laser Line".)

• Same as item 8-(b).

9

Laser line does not
match the cutting
position.

a  Improper wiring

b  Monitor failure

c  Monitor ass'y failure

d  Switching power

supply failure

------

------

------

------

• Check the wiring.

• Replace the Monitor Ass'y

[118].

• Check the Monitor Ass'y [118]

for conductivity.

• Replace the Monitor Ass'y

[118].

• Check the Switching Power

Supply [220] for conductivity.

• Replace the Switching Power

Supply [220].

10

Digital display does not
indicate anything.
(Model C 12LDH)

Содержание C 12FDH













































































Отзывы:

Нет отзывов