Hitachi Solutions StarBoard FX-E90W Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 45

background image

1-10

StarBoard FX-E90W

Introduction

English

1.4.2 Equipment Connection Method

Connect the PC, projector and StarBoard according to the following procedure.

(1) Connect the RGB cable to the projector's RGB connector, and fasten with screws.

(2) Connect the opposite side of the RGB cable to the PC's RGB connector, and fasten with

screws.

(3) Connect the USB cable from the lower left of the StarBoard to a USB port on the PC.
(4) Connect the power supply cables of the PC and projector to the power supply.

Depending on your PC, an incorrect operation might be caused by PC noise via the
USB cable. If this happens, verify that the earth of your PC's power supply cable is
connected.
If the earth is not connected, it might cause an incorrect operation.

About PC Earth

Install the StarBoard Software on your PC before starting to connect equipment. The
equipment might not operate correctly if it is connected without the software being
installed.

Before Starting to Connect Equipment

Projector

Power Supply

StarBoard

PC

«
...
21
22
23
24
25
...
»

Содержание StarBoard FX-E90W














































Отзывы:

Нет отзывов

Похожие инструкции для StarBoard FX-E90W

StarBoard FX-79E2

Бренд: Hitachi Страницы: 37

Scape Movable smo43-005

Бренд: interactive scape Страницы: 33

MALA 104.889.67

Бренд: IKEA Страницы: 16

MALA 504.565.92

Бренд: IKEA Страницы: 32

Бренд: Best-Rite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды