manualshive.com logo in svg

Hirschmann PAT TRS 05 / PATB3, Инструкция по установке и настройке, Страница: 6 / 12

Поделиться
Скачать
Hirschmann PAT TRS 05 / PATB3 Скачать руководство пользователя страница 6

 

Installation / Setup Manual  TRS 05 / PATB3 

© Hirschmann Rev. -03/09/2006 

190203_- 

2 SYSTEM 

DESCRIPTION 

2.1 RECEIVER 

MODULE 

 
The receiver module has the following functions:  
 

•

  Visual indication of receiver power, radio links (sensor on line), sensors low battery, and alarm 

conditions. 

•

 Installs/uninstalls 

a 

sensor 

•

  Allows a zero point and output adjustment of a load sensor. 

 

Red Power LED 

Red Alarm LED 

Sensor On Line 

Green LED 1 

Green LED 2 

Sensor Low Battery 

Yellow LED 1 

Yellow LED 2 

 

 

2.1.1 LEDs 
Red Power LED 

Power is applied to the circuit board. 

Red alarm LED 

An installed sensor is indicating an alarm, or communication as been 
lost to an installed sensor. 

Green LED 1 ON 

Sensor on channel #1 is installed and communicating correctly. 

Green LED 1 FLASHING 

Sensor #1 is not communicating correctly. 

Green LED 1 OFF 

No sensor is installed on channel #1. 

Yellow LED 1 ON 

Sensor #1 batteries are low and need replaced. Note that the sensor 
is still operating correctly. 

Green LED 2 ON 

Sensor on channel #2 is installed and communicating correctly. 

Green LED 2 FLASHING 

Sensor #2 is not communicating correctly. 

Green LED 2 OFF 

No sensor is installed on channel #2. 

Yellow LED 2 ON 

Sensor #2 batteries are low and need replaced. Note that the sensor 
is still operating correctly. 

Green Heartbeat LED 

This will flash during normal operation. If it is a solid or off, the 
receiver has a software error or the board has a component failure. 

 

Содержание PAT TRS 05 / PATB3













Отзывы:

Нет отзывов