Hirschmann PAT TRS 05 / PATB3 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 12

background image

Installation / Setup Manual TRS 05 / PATB3

© Hirschmann Rev. -03/09/2006

190203_-

Antenna spare parts reiteration

6608125 A2B Switch

031-300-050-763 Neoprene rubber gasket

031-300-050-672 ANTENNA, 918
MHz MAGNETICBASE 13ft long wire

031-300-050-671 ANTENNA, 918 MHz
FOR TRS05ASSEMBLY 060-576 WHIP
ELEMENT

031-300-060-559 ANTENNA ASSY, 918
MHz WHIP FORLOAD CELL

031-300-050-688 ANTENNA, 918 MHz
RCL 90°

031-300-050-535 CONNECTOR, SMA RIGHT
ANGLE M/FREVERSE POLARITY

«
...
10
11
12

Содержание PAT TRS 05 / PATB3













Отзывы:

Нет отзывов

Похожие инструкции для PAT TRS 05 / PATB3

Бренд: Datavideo Страницы: 2

MMAC-Plus 9H423-26

Бренд: Cabletron Systems Страницы: 14

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Alyseum Страницы: 7

Бренд: Audio Authority Страницы: 12

EX ZS 92 S 22 VD F

Бренд: steute Страницы: 28

Бренд: V7 Страницы: 35

Бренд: MuxLab Страницы: 32

Бренд: TRENDnet Страницы: 11

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

Бренд: Comtech EF Data Страницы: 70

Omni-Rupter Series

Бренд: S&C Страницы: 31

IES-5222T Series

Бренд: Lantech Страницы: 30

Бренд: Contec Страницы: 38

Бренд: Wetekom Страницы: 34

Бренд: SMART-AVI Страницы: 2

DCRS-5200 Series

Бренд: Digital China Networks Страницы: 4

Бренд: A SYSTEMS Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды