Hirschmann OZD Genius G12-1300 Скачать руководство пользователя страница 6

Страница: 6 / 72

Installation OZD Profi 12M ...

Release 01 07/2017



Certified usage



Use the product only for the application cases described in the
Hirschmann product information, including this manual.



Operate the product only according to the technical specifications.

See “Technical data” on page 57.



Connect to the product only components suitable for the requirements
of the specific application case.



Device casing

Only technicians authorized by the manufacturer are permitted to open
the housing.



National and international safety regulations

Verify that the electrical installation meets local or nationally applicable
safety regulations.



Grounding the device

Functional grounding the device is by means of a separate connection on
the device.



Ground the device before connecting any other cables.



Disconnect the grounding only after disconnecting all other cables.



Ground the device via the ground screw.



Requirements for connecting electrical wires



Before connecting the electrical wires,

always

verify that the

requirements listed are complied with.

All

of the following requirements are complied with:



The electrical wires are voltage-free.



The cables used are permitted for the temperature range of the application case.

Table 1:

General requirements for connecting electrical wires

All

of the following requirements are complied with:



The voltage connected complies with the requirements for a safety extra-low voltage
(SELV) as per IEC/EN 60950-1.



The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.

See “General technical data” on page 57.

Table 2:

Requirements for connecting the signal contact

Содержание OZD Genius G12-1300









































































Результаты поиска

Содержание OZD Genius G12-1300

Отзывы:

Похожие инструкции для OZD Genius G12-1300

Бренды по названию

Популярные бренды

Hirschmann OZD Genius G12-1300, Руководство пользователя

Результаты поиска

Содержание OZD Genius G12-1300

Отзывы:

Похожие инструкции для OZD Genius G12-1300

Бренды по названию

Популярные бренды