HIOS HM-10 Скачать руководство пользователя страница 14

Страница: 14 / 20

- 13 -

■

Troubleshooting (before deciding the instrument has failed)

Before deciding the instrument has failed, refer to the table below for troubleshooting. If this does
not solve the problem, please contact your dealer or HIOS.

Symptom

Possible cause

Action to take

“LOBAT” in the display

・

Insufficient charging of the

battery

・

Charge the battery. Refer to P. 11.

・

If nothing is displayed even

after charging the battery, please
contact us.

Nothing appears on the display

・

The instrument has not been

used for a long time, or the battery
has died.

・

Turn off the power and charge

the battery for about 10 minutes
and turn on the power. If the
display becomes active, then
charge the battery within eight
hours for ordinary use.

・

If it doesn’t solve the problem,

please contact us.

Cannot set it to zero

・

Reset does not work if the display

value without a load exceeds 10
digits.

・

Set the Mode switch to TRACK

and see if zero will be displayed.
(Perform this zero adjustment
in the TRACK mode occasionally
while in operation.)

The value cannot be held.

・

The Mode switch is set to TRACK.

・

Set it to PEAK.

・

Zero adjustment has not been

done.

・

The connection cable is wrongly

connected or it is broken.

・

Use the zero adjustment knob

for adjustment.

・

Replace the cable.

The instrument cannot be charged

・

The plug of the charger is not

inserted correctly.

・

Check if the plug is correctly

inserted.

・

The plug is connected to the

wrong terminal.

・

Connect it to the right

connector.

・

If it doesn’t solve the problem,

please contact us.

The LED of the charger doesn’t
turn on.

・

The cord of the charger is broken.

・

Check if the plug is connected to

the right terminal.

・

The plug of the charger is

connected to the wrong terminal.

・

If it doesn’t solve the problem,

please contact us.

After charging the battery it still
displays insufficient charging.

・

The battery died.

・

Repair is required.

・

Still insufficient charging of the

battery

・

Charge the battery again not

exceeding eight hours.

An irrelevant value is displayed

・

Noises cause wrong value

display.
(When power is on or in the PEAK
mode)

・

Press the Reset button to delete

the value.

Содержание HM-10





















Результаты поиска

Содержание HM-10

Отзывы:

Бренды по названию

Популярные бренды

HIOS HM-10, Руководство по эксплуатации

Результаты поиска

Содержание HM-10

Отзывы:

Бренды по названию

Популярные бренды