Hioki PW8001-01 Скачать руководство пользователя страница 239

Страница: 239 / 262

233

Troubleshooting

11.2 Troubleshooting

If damage is suspected, read “Before returning the instrument for repair” (p. 233) and “1 1.3
Dialogs” (p. 236) to remedy the issue. If the issue cannot be resolved, contact your authorized
Hioki distributor or reseller.

Before returning the instrument for repair

Check the following items.

Issue

Cause

Solution and where to find

additional information

The time and date are

significantly deviated after the

instrument was turned on.

A backup lithium battery is

installed in the instrument. The

service life of the backup battery

is about 10 years.

If the battery requires replacement,

the battery cannot be replaced by the

customer. Contact your authorized

Hioki distributor or reseller.

Nothing is shown on the

screen when the power switch

is turned on.

The power cord is not connected

to the instrument.

The power cord is improperly

connected.

Verify that the power cord is

connected properly.

See “2.4 Supplying Power to the

Instrument” (p. 39).

The keys are not functioning.

The instrument is in the key-lock

state.

Press and hold the

REMOTE/

LOCAL

key for at least 3 s to cancel

the key-lock state.

The screen does not react even

when you use the touchscreen.

•

The instrument is in the key-

lock state.

•Foreign material, such as dust,

settles on the touchscreen.

•Press and hold the

REMOTE/

LOCAL

key for at least 3 s to

cancel the key-lock state.

•Remove the dust or other foreign

material.

See “Replaceable parts and service

life” (p. 232).

The instrument’s settings

cannot be changed.

The instrument is performing

integration or stopped performing

integration.

Perform an integrated value reset

(data reset).

See “3.3 Integrating Current and

Power” (p. 64).

The instrument cannot display

any measured voltage or

current values.

The voltage cords and current

sensors are improperly

connected.

Check the connections.

See “2 Preparing for

Measurement” (p. 31).

The input channel and display

channel do not match with each

other.

(For example, this issue will arise

if the input channel has been set

to Ch. 1 while a page other than

the

CH1

page has been being

displayed.)

Use the





keys for channel

selection to display the page for the

input channel.

See “3.2 Measuring Power”

(p. 53).

The active power is not

displayed.

The voltage and current range

settings is improperly configured.

Set the voltage and current ranges

properly.

See “Voltage range and current

range” (p. 54).

Maintenance and Service

HIOKI PW8001A961-00

Содержание PW8001-01







































































































































































































































































Результаты поиска

Содержание PW8001-01

Отзывы:

Похожие инструкции для PW8001-01

Бренды по названию

Популярные бренды

Hioki PW8001-01, Инструкция по эксплуатации

Результаты поиска

Содержание PW8001-01

Отзывы:

Похожие инструкции для PW8001-01

Бренды по названию

Популярные бренды