Hioki MR8827 Скачать руководство пользователя страница 245

Страница: 245 / 436

240

Display Settings

12.2 Display Settings

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Memory Div]

sheet.

To display any block on the Waveform screen
Set the display blocks

Set after measurement is complete. (This can also be set on the

Waveform screen (p. 137).)

Move the cursor to

[Display Block]

Set the number of blocks to display on the Waveform screen.

Trigger time Reference Block No.

When the Display Block is 5 and

the Reference Block is 3

The colored blocks indicate blocks

where measurement data has been

recorded.

Reference Block (Light Green)

Display Block (Green)

Reference Block Selection

Reference Blocks can also be selected

and deselected using

[Ref Block]

the [List] display.

Refer to “To get details on each block”

(p. 241).

Setting the Trace Waveform display

[On]

lengthens dead time.

About Dead Time:

Refer to “Difference Between Dead

Times During Normal and Memory

Division Recording” (p. 242).

Even if the Roll Mode is enabled (other

than

[Off]

), it is not usable when the

Trace Waveform display is set to

[Off]

To display multiple blocks as overlaid waveforms
Enable the Reference Block function

Move the cursor to

[Ref Block]

Select

[On]

Off

Reference Blocks are not displayed

(Default setting)

Reference Blocks overlay Display blocks on the display.

(When Reference Blocks are enabled [On])
Select whether to reference every block

To overlay all waveforms, select

[All Blks On]

All Blks Off

Turn off reference to all blocks.

All Blks On

Turn on reference to all blocks.

To overlay selected waveforms, move the cursor to the number

column of the reference block and select the block number.

Ref On-Off

Set On or Off. If

[On]

is selected, the block

frame of the selected block number is

displayed as a green square.

↑↓

Select a block.

To display every block as its waveform is acquired
Enable tracking waveform display.

Move the cursor to

[Wave Display]

Select

[On]

Off

The waveform of the specified Display Block will be

displayed after recording the specified number of Used

Blocks.

(Default setting)

Waveforms are displayed one block at a time as they

are acquired at each trigger event.

To View Memory Division waveforms on the Waveform

screen

Refer to “7.8 View Block Waveforms” (p. 137)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды