Hioki MR8827 Скачать руководство пользователя страница 247

Страница: 247 / 436

242

Display Settings

Difference Between Dead Times During Normal and Memory Division Recording

When both printer recording (Auto Print) and Auto Save are set for continuous triggering

[Repeat]

Dead Times

Times during which sampling is inhibited due to internal processing, printing or saving

Recording

Length

Anomalous phenomena occurring during dead times are not detected.

When the Trace Waveform Display is disabled (

[Off]

) during Memory Division recording

Recording

Length

Dead Times

The waveform data of each recording length is recorded in one block.

When recording with Memory Division, dead time is shorter than with normal recording.

• The dead time (the period where no sampling occurs between blocks) of memory division is as

follows.

5 μs/div to 20 μs/div: 1 to 8 samples

Timebase slower than 50 μs/div: 1 sample

Note: Dead time is longer when you use calculation functions or when the timebase is set between 5

and 20 μs/div and tracking waveform display is

[On]

•

When measuring with an Model 8970 Freq Unit, dead time is approximately 230 ms. When measuring

in integral value ([Count]) mode, there are cases when the last data in a previous block is carried over

to the first part of the next block.

• When tracking waveform display is

[Off]

, the roll mode function cannot be used, even when roll mode

is enabled (not

[Off]

• When triggering occurs very often, pressing the

STOP

key may not stop measurement until enough

data has been acquired to fill the blocks specified for use.

Auto Save and Auto Print for Memory Division Recording

Measurement conditions Auto-save and Auto-print

With Numerical calculation

Auto-save and Auto-print are performed every time one block is measured. When

Tracking wave display is ON, the Waveform is also displayed.

When timebase is 5 μs/div

to 20 μs/div and Tracking

wave display is ON.

Auto-save, auto-print and Waveform Display are performed every time one block is

measured.

When timebase is 5 μs/div

to 20 μs/div and Tracking

wave display is OFF.

Auto-save and Auto-print are performed after all blocks are measured.

Other than above

Auto-save and Auto-print are performed simultaneously with measurement. When

Tracking wave display is ON, the Waveform is also displayed.

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Hioki MR8827, Инструкция по эксплуатации, Страница: 247 / 436

Результаты поиска

Содержание MR8827

Отзывы: