Hioki MR8827 Скачать руководство пользователя страница 193

Страница: 193 / 436

188

Setting Workflow

9.1

Setting Workflow

Trigger Mode Settings

This setting controls whether the instrument

continues to accept triggers after measuring.

(p. 189)

Trigger Type Settings

Make trigger source-related settings.

•

Analog trigger

•Logic trigger

•Timer Trigger

•External Trigger

•Manual trigger

Pre-trigger Settings

Set the amount to record before and after trigger

points.

(p. 201)

Trigger Timing Settings

Set the start and stop timing for triggered

recording.

(p. 204)

Set AND/OR Between Trigger Sources

Select the required AND/OR logical combination of

analog, logic, external and timer triggers.

(p. 206)

Start Measurement

Press the

START

key to start measurement. (The key will light

up in green.)

(Operation may differ depending on the

START

key behavior

settings (p. 307).)

Data acquisition starts when trigger criteria are met.

To stop measurement, press the

STOP

key.

Press once: Recording will stop at the end of the specified

recording length.

Press twice: Recording stops when the key is pressed.

Available settings for the respective items depend on the

function.

•

Except for manual trigger, triggering is based on the logical combination of trigger sources (AND/OR).

(p. 206)

•

When triggering occurs, the TRIG OUT terminal for control of external devices carries an output

signal. (p. 343)

Содержание MR8827




















































































































































































































































































































































































































































Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды

Hioki MR8827, Инструкция по эксплуатации

Результаты поиска

Содержание MR8827

Отзывы:

Похожие инструкции для MR8827

Бренды по названию

Популярные бренды