Hioki IM7580 Скачать руководство пользователя страница 25

Страница: 25 / 340

Connecting the Test Head

Measurement Preparations

Please read “Operating Precautions” (p. 6) before installing and connecting this instrument.

See “Rack Mounting” (p. A7) for rack mounting.

2.1 Connecting the Test Head

Connect the test head.

See “5 Calibration and Compensation” (p. 139).

CAUTION

•

If the instrument and the connectors of the test head are not correctly connected, the

instrument may get damaged or accurate measurements may not be possible.

•

Tighten the connector with a torque of 0.56 N.m (recommended value). Tightening

the connector with a torque other than the recommended value, may damage the

instrument or accurate measurements may not be possible.

IMPORTANT

•

Check that there are no problems with the connector before connecting the cable. If

there is a problem with the connector, you cannot perform accurate measurement due

to large measurement errors.

Refer to “Appx. 5 Maintenance of Coaxial Connector” (p. A6)

•

The instrument is adjusted in combination with the test head and the connection cable.

Make sure to connect the test head having the identical serial number as the instrument

via the connection cable included with shipment.

Rear of the instrument

Rear of the test head

Serial No.

2 Measurement Preparations

Measurement Preparations

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды