Hioki IM7580 Скачать руководство пользователя страница 318

Страница: 318 / 340

Maintenance of Coaxial Connector

Appx. 5 Maintenance of Coaxial Connector

Because the coaxial connector is highly accurate, reproducibility will deteriorate even in case of

small bends, damages and dust etc.

Connecting a coaxial connector with dust or defects may damage the connector of the instrument.

Do not use a coaxial connector with defects.

Before measurement, visually inspect the connector to make sure that the coaxial connector is not

defective.

Visual inspection of the connector

(Using a magnifying glass is recommended.)

Screw

Must not have any burrs or metal fragments attached, crushed, or have scratches.

Nut

Smooth movement.

Outer

conductor

The contact surface must be free from dust, dirt, or scratches.

Inner

conductor

•

The contact surface must be free from dust, dirt, scratches or defects.

•

The contact must be free from extreme bending or opening.

•

Must not be eccentric with respect to the outer conductor.

Full contact

Slight opening of the contact

(Resistant to normal use)

Excessive bend of the

contact (Cannot be used)

Connector cleaning

• Blow low-pressure air.

•

Apply little alcohol to a cotton swab, and clean the contact surface and the screw thread.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды