Hioki IM7580 Скачать руководство пользователя страница 147

Страница: 147 / 340

139

Calibration and Compensation Function Overview

Calibration and Compensation

5.1 Calibration and Compensation Function

Overview

It is necessary to perform open/short/load calibration on the instrument prior to measurement.

In addition, electric length compensation, and open/short compensation are performed when

necessary.

Open/Short/Load Calibration

Connect the 3 standards, open, short and load to the reference surface (terminal) one by one,

and measure respective calibration data. The reference surface is referred to as the “calibration

reference surface”. The cause of errors between the measurement instrument and the calibration

reference surface is eliminated. If this calibration is performed for the terminal connected to a test

sample, other calibration or compensation is not required.

Electric Length Compensation

The electric length is entered as a numerical value between the calibration reference surface on

which open/short/load calibration was performed to the surface where a measurement sample is

connected. The error caused by the phase shift between the calibration reference surface and the

measurement sample connection surface is compensated.

If a test fixture is to be used by connecting to the calibration reference surface of the test head, the

electric length of the fixture is required to be input.

Open/Short Compensation

If a test sample is to be connected to the terminal extended from the calibration reference surface

on which open/short/load calibration was performed, compensation data is measured keeping

the test sample connection terminal in the open state. In addition, the terminal is shorted, and the

compensation data is measured. The cause of errors between the calibration reference surface and

the surface on which open/short compensation was performed is eliminated. This compensation is

required to be performed if the coaxial terminal of the test head is the calibration reference surface.

5 Calibration and Compensation

Calibration and Compensation

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды