Hioki FT3151 страница 100 Скачать руководство пользователя

Страница: 100 / 132

Measuring Earth Resistance Simply

(Simplified Measurement, 2-Pole Measurement Method)

Settings for 2-pole measurement

Set the

Poles

selector to 2.

Setting the measurement frequency

Select the measurement frequency between 575 Hz and 600 Hz by

switching the Hz selector. Usually, set the frequency to 575. If the needle of

the galvanometer fluctuates during measurement, set the frequency to 600.

Switching the measurement frequency enables the instrument to be less

affected by a harmonic earth voltage.

Battery check

Set the range selector to the mark

press the

MEASURE

button, and

check if the needle of the galvanometer

rests within the range of the mark

. Perform this check in the

actual measurement condition with the

measurement leads already connected.

If the needle of the galvanometer does not reach the range of

the mark

, replace the batteries with fresh ones. See “4.2

Inserting/Replacing Batteries” (p. 52).

Содержание FT3151





































































































































Результаты поиска

Содержание FT3151

Отзывы:

Похожие инструкции для FT3151

Бренды по названию

Популярные бренды

Hioki FT3151, Инструкция по эксплуатации

Результаты поиска

Содержание FT3151

Отзывы:

Похожие инструкции для FT3151

Бренды по названию

Популярные бренды