Hinowa LightLift 15.70 3S Скачать руководство пользователя страница 112

Страница: 112 / 137

112

The TEACH IN procedure must be carried out when one joystick has been
replaced, to enter into TEACH IN mode it has to be kept pressed for 7 seconds

buttons n.1, n.6 and the one in the right-lower corner.

On the display will appear “JOY TEACH” and the instructions to calibrate the

joysticks, it has to be move each joystick completely down and completely up,

then all of them must be centred on idle position and press button n.7, after
that the remote control will come back into normal mode.

APPENDIX 4

–

REMOTE CONTROL STOP BUTTON BY-PASS

With machine stabilized while remote control is connected to its basket

connector with stop button pressed, in case of an emergency it’s possible to

by-pass it keeping turned rightward the control position selector and switching

ON one motor by its ignitions button.

While control position selector is kept pressed it’s possible to move the aerial

part acting on the aerial part valveblock levers, as soon as control position
selector or remote control stop button are released, the motor will switch OFF

immediately.

NOTE: With lithium machines, control position selector kept turned rightward

will also get the electric motor running.

CONTROL POSITION

SELECTOR SWITCH

AERIAL PART MOVEMENTS LEVERS

MOTORS INGNITION

BUTTONS

AERIAL PART MOVEMENTS

INDICATIONS

+ +

Содержание LightLift 15.70 3S










































































































































Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды

Hinowa LightLift 15.70 3S, Техническое руководство

Результаты поиска

Содержание LightLift 15.70 3S

Отзывы:

Похожие инструкции для LightLift 15.70 3S

Бренды по названию

Популярные бренды