Hinds Instruments PEM200 Скачать руководство пользователя | Manualshive

Страница: 7 / 72

background image

PEM200 User Manual

3

High Voltage (HV) SMA connectors support hazardous electrical levels, up to 138Vrms.
Contact with High Voltage (HV) SMA outputs may cause severe shock or burn. Power
off the unit before connecting or disconnecting SMA cables to connectors and optical
head.

Avoid contact with SMA cable-ends or connectors other than to connect or disconnect
controller to optical head. Always connect or disconnect SMA cables with power off. Do
not turn on power until all cables are connected properly.

DC Power Supply

This product is intended to operate from a DC power source at 24 VDC. The main
power input is 90-264VAC, 47-63 Hz, 1.7A. A protective ground connection by way of
the grounding connector in the power cord is required for safe operation. Power line
requirements are listed in the specifications section.

The power cord provided with this instrument is less than 3 meters in length.
Use only the power cord and connector specified for your product to work with your
local power outlets. Use only a power cord that is in good condition.

The appliance inlet or plug on cord should always be positioned to be accessible by the
operator. To disconnect all power from the instrument, pull the power cord from the wall
outlet or from the appliance inlet. See Operating Space below for detail.

WARNING:

Hazardous Voltage

«
...
5
6
7
8
9
...
»

Содержание PEM200









































































Отзывы:

Нет отзывов

Похожие инструкции для PEM200

Бренд: Sharp Страницы: 4

WriteView ELW506X

Бренд: Sharp Страницы: 2

WriteView EL-W535XG

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 2

Бренд: Yamaha Страницы: 4

Бренд: Blonder tongue Страницы: 16

ALGEBRA FX 2.0 Plus

Бренд: Casio Страницы: 1

Бренд: Victor Страницы: 56

Бренд: IKUSI Страницы: 3

Бренд: Casio Страницы: 22

Бренд: Casio Страницы: 30

Бренд: Eurotops Страницы: 17

Бренд: GSS Страницы: 22

Бренд: GSS Страницы: 30

HDTV 1000 ASI LAN

Бренд: GSS Страницы: 45

HDMT 1000 ASI LAN

Бренд: GSS Страницы: 43

Бренд: GSS Страницы: 48

Бренд: Wang Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды