HIMA HIMax X-SB 01 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

HIMA HIMax X-SB 01 Скачать руководство пользователя страница 22

4 Start-up

X-SB 01

Page 22 of 38

HI 801 007 E Rev. 4.00

4.2 Mounting

and

Removing the Module

When replacing an existing module or mounting a new one, follow the instructions given in
this chapter.

When removing the module, the connector board remains in the HIMax base plate. This
saves additional wiring effort since all field terminals are connected via the connector board
of the module.

4.2.1 Mounting

and

Removing the Module

This chapter describes how to mount and remove the HIMax module. A module can be
mounted and removed while the HIMax system is operating.

NOTICE

Damage to bus and power sockets due to module jamming!

Failure to observe this can damage the controller.

Always take care when inserting the module in the base plate.

Tools and utilities

Screwdriver, slotted 0.8 x 4.0 mm

Screwdriver, slotted 1.2 x 8.0 mm

Installation

1. Open the cover plate on the fan rack:

;

Move the locks to the

open

position.

;

Lift the cover plate and insert into the fan rack

2. Insert the top of the module into the hook-in rail, see

.

3. Swivel the lower edge of the module towards the base plate and apply light pressure to

snap it into place, see

.

4. Tighten the screws, see

.

5. Pull the cover plate out of the fan rack and close it.
6. Lock the cover plate.

Removal

1. Open the cover plate on the fan rack:

;

Move the locks to the

open

position.

;

Lift the cover plate and insert into the fan rack

2.

Release the screw

.

3. Swivel the lower edge of the module away from the base plate. Lift and apply light

pressure to remove the module from the hook-in rail, see

and

.

4. Pull the cover plate out of the fan rack and close it.
5. Lock the cover plate.

«
...
20
21
22
23
24
...
»

Содержание HIMax X-SB 01







































Отзывы:

Нет отзывов