8
en
8. Tools and accessories
Chucks
TE 46 / TE 46-ATC
TE-T
TE 56 / TE 56-ATC
TE-Y
Hammer drill bits
TE 46 / TE 46-ATC
6–32 mm dia. (
1
/
4
″
–1
1
/
4
″
dia.)
TE 56 / TE 56-ATC
12–40 mm dia. (
1
/
2
″
–1
1
/
2
″
dia.)
Breach bits
TE 46 / TE 46-ATC
40 mm dia. (1
1
/
2
″
dia.)
TE 56 / TE 56-ATC
40–66 mm dia. (1
1
/
2
″
–2
3
/
4
″
dia.)
Percussion core bits
TE 46 / TE 46-ATC
50–90 mm dia. (2
″
–3
1
/
2
″
dia.)
TE 56 / TE 56-ATC
45–90 mm dia. (1
3
/
4
″
–3
1
/
2
″
dia.)
Diamond core bits PCM
TE 46 / TE 56
–
TE 46-ATC / TE 56-ATC
42–87 mm dia. (1
5
/
8
″
–3
3
/
16
″
dia.)
Chisels
Pointed, flat and shaped chisels
TE 46 / TE 46-ATC
with TE-T connection end
TE 56 / TE 56-ATC
with TE-Y connection end
Setting tools
TE 46 / TE 46-ATC
Setting tools with TE-T connection end
TE 56 / TE 56-ATC
Setting tools with TE-Y connection end
Quick-release chuck
Quick-release chuck 60208 for wood and metal drill
bits with cylindrical or hex. shank
TE 46 / TE 46-ATC
Chuck holder 264758
TE 56 / TE 56-ATC
Chuck holder 263359
Wood drill bits
10–32 mm dia. (
3
/
8
″
–1
1
/
4
″
dia.)
Metal drill bits
Up to 20 mm dia. (
3
/
4
″
dia.)
Mixing non-inflammable substances
Mixing paddles with cylindrical
or hex. shanks of 80–150 mm dia. (3
1
/
8
″
–6
″
dia.)
Dust removal system
TE DRS-S 340602
9. Troubleshooting
Fault
Possible cause
Remedy
The tool doesn't start
Fault in mains supply
Plug in another electric appliance and
check whether it works.
Supply cord or plug defective
The cord should be checked and, if neces-
sary, replaced by an electrical specialist.
Control switch defective
The switch should be checked and, if neces-
sary, replaced by an electrical specialist.
No hammering action
The tool is too cold
Allow the tool to warm up to the minimum
operating temperature. (See "Operation".)
Function selection switch set to
Set the function selection switch to
rotary drilling (TE 46-ATC/TE 56-ATC)
hammer drilling.
The tool does not achieve
Extension cord with inadequate cross Use an extension cord with adequate cross
full power.
section used
section. (See "Before use".)
Control switch not fully pressed
Press the control switch as far as it will go.
"Reduced power" button activated
Press the "reduced power" button (fig. 1).
Drill bit doesn't rotate
Function selection switch not engaged After rotation has stopped, move the
function selection switch until it engages.
The drill bit cannot be
Chuck sleeve not pulled back fully
Pull the chuck sleeve back as far as it will
released from the chuck
go and remove the insert tool.
Side handle not correctly fitted or
Release the side handle and reposition it
moved out of place
correctly so that the clamping band and
side handle are engaged in the groove.
(See 5.1)
Printed: 07.07.2013 | Doc-Nr: PUB / 5070956 / 000 / 00
