Hilti PM 2-P Скачать руководство пользователя страница 7

Battery life

Alkaline battery 2,500 mAh, Tempe24°C: 50 h

(Typical)

Operating temperature range

Min. -10°C / Max. +50°C

Storage temperature

Min. -25°C / Max. +63°C

Dust and water spray protection (except battery com-

partment)

IP 54 as per IEC 529

Tripod thread (tool)

UNC¹⁄₄"

Tripod thread (foot)

BSW ⁵/₈" UNC ¹/₄"

Dimensions

63 x 107 x 137 mm

Weight

With foot and batteries: 590 g

1 Influences such as particularly high temperature fluctuations, dampness, shock, dropping, etc. can affect accuracy. Unless stated

otherwise, the tool was adjusted or calibrated under standard ambient conditions (MIL-STD-810F).

5 Safety instructions

WARNING: Ensure that you read all safety precautions

and instructions.

Failure to observe the safety precau-

tions and instructions may result in electric shock, fire

and/or serious injury.

Retain all safety precautions and

instructions for future reference. .

5.1 General safety rules

a)

Check the accuracy of the tool before using it to

take measurements.

b)

The tool and its ancillary equipment may present

hazards when used incorrectly by untrained per-

sonnel or when used not as directed.

c)

To avoid the risk of injury, use only genuine Hilti

accessories and additional equipment.

d)

Stay alert, watch what you are doing and use com-

mon sense when operating the machine. Don’t

use the machine when you are tired or under the

influence of drugs, alcohol or medication.

A mo-

ment of inattention while operating machines may

result in serious personal injury.

e)

Modification of the tool is not permissible.

f)

Observe the information printed in the operat-

ing instructions concerning operation, care and

maintenance.

g)

Do not render safety devices ineffective and do

not remove information and warning notices.

h)

Keep laser tools out of reach of children.

i)

Take the influences of the surrounding area into

account. Do not expose the tool to rain or snow

and do not use it in damp or wet conditions. Do

not use the tool where there is a risk of fire or

explosion.

j)

Maintain the machine carefully. Check for mis-

alignment or binding of moving parts, breakage

of parts and any other condition that may affect

the machine’s operation. If damaged, have the

machine repaired before use.

Poor maintenance is

the cause of many accidents.

k)

Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

l)

The user must check the accuracy of the tool

after it has been dropped or subjected to other

mechanical stresses.

m)

When the tool is brought into a warm environment

from very cold conditions, or vice-versa, allow it

to become acclimatized before use.

n)

Make sure that the tool is mounted securely when

adapters or accessories are used.

o)

Keep the laser exit aperture clean to avoid meas-

urement errors.

p)

Although the tool is designed for the tough condi-

tions of jobsite use, as with other optical and elec-

tronic instruments (e.g. binoculars, spectacles,

cameras) it should be treated with care.

q)

Although the tool is protected to prevent entry

of dampness, it should be wiped dry each time

before being put away in its transport container.

r)

Check the accuracy of the measurements several

times during use of the tool.

5.2 Proper organization of the work area

a)

Secure the area in which you are working and

take care to avoid directing the beam towards

other persons or towards yourself when setting

up the tool.

b)

Avoid unfavorable body positions when working

from ladders. Make sure you work from a safe

stance and stay in balance at all times.

c) Measurements taken through panes of glass or other

objects may be inaccurate.

d)

Ensure that the tool is set up on a steady, level

surface (not subject to vibration).

e)

Use the tool only within its specified limits.

f)

If several laser tools are used in the same working

area, care must be taken to avoid confusing the

beams.

en

4

Printed: 08.07.2013 | Doc-Nr: PUB / 5130772 / 000 / 01

Содержание PM 2-P













Отзывы: