16
English
2272031
*2272031*
7.2
Cutting
▶
When cutting, keep the rate of advance moderate and do not tilt the product or the cut-off wheel to either
side (working position is at approx. 90° to the cutting plane).
For best results when cutting profiles and small rectangular tube, start cutting with the cut-off
wheel at the smallest cross-section.
7.3
Rough grinding
WARNING
Risk of injury.
The abrasive cut-off wheel could shatter and flying fragments may cause injury.
▶
Never use abrasive cut-off wheels for grinding.
▶
Move the product to and fro while maintaining a 5° to 30° angle of attack and applying moderate pressure.
▶
This will avoid overheating and discoloration of the workpiece and help ensure an even surface finish.
7.4
Switching on (tool equipped with switch-on interlock)
The on / off switch with switch-on interlock gives you full control of the switch function and avoids
unintentional starting of the product.
1. Push the switch-on interlock forward.
▶
The on/off switch is unlocked.
2. Press the on/off switch as far as it will go.
▶
The power tool’s motor runs at no-load speed.
7.5
Switching off, on/off switch with built-in switch-on interlock
▶
Release the on/off switch.
▶
The switch-on interlock jumps automatically into the locked position.
8
Care and maintenance
WARNING
Risk of injury with battery inserted
!
▶
Always remove the battery before carrying out care and maintenance tasks!
DANGER
Electric shock due to breakdown of protective insulation.
When working on metal under extreme
conditions, conductive dust (e.g. metal, carbon fiber) may accumulate inside the power tool, thereby
adversely affecting the protective insulation.
▶
Use a stationary dust extraction system when working under extreme conditions.
▶
Clean the air vents frequently.
Care of the product
• Carefully remove stubborn dirt.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as
these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of
moisture (e.g. by being dipped in water or left in the rain).
If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable
container and consult
Hilti
Service.
Содержание NURON AG 5D-22 125
