Hilti DX 462 Скачать руководство пользователя страница 3

17

en

3. Cartridges, accessories and fasteners

Accessories

Ordering designation

Application

Splinter guard

An additional baseplate that helps to keep the tool perpendicular when pressed
against the base material and to reduce splintering (for use with standard fastener
guide only).

X-PT 460

Also known as the pole tool. An extension system for various applications on ceilings.

Fastener guides

Ordering designation

Application

X-462-F8

Standard fastener guide.

X-462-F8S12

Fastener guide for nails with a 12 mm steel washer for higher pull-over loads.

Pistons

Ordering designation

Application

X-462-P8

Standard piston.

X-462-P8AL

AL piston for AL nails. Achieves better nail guidance and thus increases the application limit.

Fasteners

Ordering designation

Application

X-DNI, X-ZF

Nail with a wide range of uses. Suitable for various types of fastenings.

X-EDNI

Standard nail for efficient fastenings on steel.

X-EDNI…S12

Standard nail for efficient fastenings on steel. With 12 mm washer for higher pull-over
loads.

X-DAK

Nail with stepped shank. For fastening on high-strength concrete or steel.

X-CR

Stainless steel nail for fastenings in damp or corrosive surroundings.

X-AL-H

High-strength nail for fastening on high-strength steel or concrete.

X-SW

Nail with flexible washer for fastening plastic insulating sheeting on concrete or steel.

X-(D)FB

Metal clip for fastening electric conduits / ducts and insulated water or heating pipes
(hot or cold).

X-CC

Clip for fastening wire or chain hangers.

X-HS

Suspension system with threaded boss.

X-(E)M6/8

Threaded studs for temporary fastenings on concrete and steel.

Please contact your local Hilti Center or Hilti representative for details of other fasteners and accessories.

Cartridges

Ordering designation

Colour code

Power level

6.8/11 M green

Green

Low

6.8/11 M yellow

Yellow

Medium

6.8/11 M red

Red

Heavy

6.8/11 M black

Black/purple

Extra heavy

Safety accessory and cleaning set

Safety goggles, earplugs, Hilti spray, ramrod, flat brush, large round brush, small round brush, scraper, cleaning
cloth.

Содержание DX 462















Отзывы: