Hilti DX 460 SM Скачать руководство пользователя

Страница: 14 / 19

Cartridge not transported

Cartridge strip cannot be
removed

Troubleshooting

Fault

Cause

■

Damaged cartridge strip

■

Carbon build up

■

Tool damaged

■

Tool overheated because of high
setting rate

■

Tool damaged

WARNING

Make sure not to crush or pry
on an unfired booster.

■

Bad cartridge

■

Carbon built up

WARNING

Never attempt to pry a cartridge
from the magazine strip of the tool.

Possible remedial measure

■

Change cartridge strip

■

Clean the cartridge strip guide-
way (see 8.4, point 5)

If the problem persists:

■

Contact Hilti Center.

■

Let the tool cool down

■

Then carefully try to remove the
cartridge strip

If not possible:

■

Contact Hilti Center.

■

Manually advance the cartridge
strip one cartridge
If the problem occurs more
often: Clean the tool

If the problem persists:

■

Contact Hilti Center.

■

Tool is compressed too long
while fastening.

■

Fastening frequency is too high

■

Compress the tool a shorter time
while fastening.

■

Remove the cartridge strip

■

Disassemble the gas return unit
(see 8.4) for fast cooling and to
avoid possible damage

If the tool cannot be disassembled:

■

Contact Hilti Center.

Cartridge strip melts

Cartridge cannot be fired

Cartridge falls out of the
cartridge strip

■

Fastening frequency is too high

WARNING

Make sure not to crush or pry
on an unfired booster

■

Immediately discontinue using
the tool and let it cool down

■

Remove cartridge strip

■

Let the tool cool down.

■

Clean the tool and remove loose
cartridge.

If it is impossible to disassemble
the tool:

■

Contact Hilti Center.

Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01

Содержание DX 460 SM




















Результаты поиска

Содержание DX 460 SM

Отзывы:

Похожие инструкции для DX 460 SM

Бренды по названию

Популярные бренды

Hilti DX 460 SM, Руководство по эксплуатации

Результаты поиска

Содержание DX 460 SM

Отзывы:

Похожие инструкции для DX 460 SM

Бренды по названию

Популярные бренды