G
G
CAUTION
Wear protective gloves, especially when changing
discs, adjusting the guard (hood) and when fitting the
hood extension with depth gauge.
6.1 Guard (hood)
WARNING
Never use the power tool without the guard (hood).
NOTE
If the guard (hood) clamping force is found to be inad-
equate, this can be increased by tightening the clamping
screw slightly.
6.1.1 Fitting and adjusting the guard (hood)
5
1. Disconnect the supply cord plug from the power
outlet.
2. Use the hex. socket wrench to release the clamping
screw.
3. Fit the guard (hood) onto the collar on the gearing
section.
4. Rotate the guard (hood) into the desired position.
5. Use the hex. socket wrench to tighten the clamping
screw.
6.1.2 Removing the guard (hood)
1. Disconnect the supply cord plug from the power
outlet.
2. Use the hex. socket wrench to release the clamping
screw.
3. Rotate the guard (hood) and pull it away from the
tool.
6.2 Depth gauge (optional)
DANGER
The hood extension with depth gauge is to be used
exclusively for cutting mineral materials with diamond
discs.
6.2.1 Fitting / removing the hood extension with
depth gauge
4
1. Disconnect the supply cord plug from the power
outlet.
2. Fit the hook over the guide wheel axle.
3. Pivot the hood extension into the hood until the
catch is heard to engage.
4. To remove the hood extension, press the catch and
pivot the hood extension down and away from the
hood.
6.2.2 Using the depth gauge to adjust cutting depth
1. Press the cutting depth sliding indicator.
2. Move the cutting depth sliding indicator to the de-
sired cutting depth.
6.3 Fitting a cutting disc
CAUTION
Use only cutting tools with a rated maximum permiss-
ible speed which is at least as high as the machine’s
highest no-load running speed.
CAUTION
Cutting discs which are damaged or out of round
(causing vibration) must not be used.
CAUTION
Do not use synthetic resin-bonded fiber-reinforced
cutting discs that have exceeded their use-by date.
NOTE
Diamond cutting discs in compliance with the require-
ments of EN 13236 are to be used with the power tool.
Synthetic resin-bonded fiber-reinforced cutting discs in
compliance with EN 12413 (straight, not offset, type 41)
may also be used with this power tool for working on
metals. In this case, the appropriate DCH 300 ABR disc
mount (see accessories) must be used with the power
tool. The mounting instructions issued by the disc man-
ufacturer must also be observed.
NOTE
Diamond discs must be replaced when the cutting or
grinding performance drops significantly. This generally
is the case when the segments reach a height of less
than 2 mm.
6.3.1 Fitting diamond cutting discs
The segments must have a negative rake angle and the
size of the gap G between the segments must not exceed
10 mm. The maximum disc thickness is 3.5 mm.
The 60 mm diameter reversible flange is used for mount-
ing cutting discs with arbor size 22.2 mm or 25.4 mm.
Check which side of the flange fits the arbor hole in the
cutting disc. The flange must center the disc.
en
26
Printed: 06.02.2015 | Doc-Nr: PUB / 5069502 / 000 / 02
Содержание DCH 300
Страница 2: ...1 Printed 06 02 2015 Doc Nr PUB 5069502 000 02 ...
Страница 3: ...DCH EX 300 6 5 ø 300 ø 60 ø 60 DCH EX 300 6 ø 60 ø 80 ø 300 ø 80 2 3 ...
Страница 4: ...2 1 3 Ç 4 ...
Страница 5: ...1 2 3 4 5 5 ...