manualshive.com logo in svg

Hillsboro 2500 Series, Руководство пользователя

Поделиться
Скачать
Hillsboro 2500 Series Скачать руководство пользователя страница 13

FUEL FILLER INSTALLATION

 

 

 
 
 
 
 
 
 

 

 

WARNING:

   

Keep  all ignition  sources  away  from  vehicle  when  working  with  Fuel 

Tank Filler Pipe. 
 

 

CAUTION: 

Fuel  Tank  Filler  Pipe  must  be  installed  according  to  vehicle 

manufacturer  requirements.  Follow  all  warnings  and  cautions  within  the  vehicle 
manual. 
  

 

Locate  and  identify  all  components  supplied  with  the  Fuel 
Filler  Mounting  Kit.    Hardware  is  packaged  in  a  padded 
envelope.  Determine  the  desired  location  along  the  side  of 
the  bed  for  the  fuel  filler  installation.    Location  must  avoid 
interference of fuel tank fill tube with bed crossmembers and 
be  no  closer  than  4  inches  to  any  stake  pocket.    Mark 
selected filler centerline on tie strap and bed. 
 

 

Remove  4  1/2  inches  of  tie  strap  centered  on  fuel  filler 
centerline.  Cut a 2 1/2 inch diameter hole in the side of the bed 
located on fuel filler centerline and 2 5/8 inches downward from 
the  top  surface  of  bed.      Remove  all  burrs  remaining  after 
cutting. 
      
Insert fuel tank fill  pipe  through  hole  in  bed  side.    Connect fuel 
tank  fill  pipe  to  tank  according  to  vehicle  manufacturer 
requirements. 
      
Slide  fuel  filler  mount  down  from  the  top  behind  tie  strap  and 
over  fuel  fill  pipe,  until  the  top  of  the  mount  is  flush  with  the  top  of  tie  strap.    Clamp  fuel  filler 
mount in place.  Drill upper 3/8 inch holes through tie strap, both flanges of filler mount, and bed.  
Upper holes are centered vertically on the tie strap and 1/2 inch from cut edge, 2 places.  Drill 
lower  3/8  inch  holes  through  filler  mount  and  bed.    Lower  holes  are  3/8  inch  from  bottom  and 
edge of filler mount, 2 places. 
      
Install  carriage  bolts  from  outside.    Install  flat  washer,  lock  washer  and  hex  nuts,  6  places.  
Tighten nuts to approximately 13 ft. lbs.  Fasten fuel filler pipe flange to filler mount as required 
by vehicle manufacturer specifications. 

Page 11 

Содержание 2500 Series















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды