background image

7

Warranty

5. This warranty is in addition to any non-excludable legal rights or remedies conferred  

on the consumer under any applicable Act and any similar laws. To the extent 
permitted by law, Hills' liability for any non-excludable condition or warranty is limited  
to rectifying any defect at its option, as set out in paragraph 4(b).

6. Subject to the requirements of any applicable Act or legislation and to the extent 

permitted by law, no liability (whether expressed or implied) of any nature whatsoever, 
is accepted by Hills for any consequential loss, damage or injury arising as a result  
of any fault in the Products.

7. This warranty does not extend to damage to Products which occurs during transit  

or transportation, or which is caused by any abuse, accident or improper installation, 
connection, use, adjustment or repair or use of goods otherwise than in accordance 
with instructions issued by Hills.

8. The warranty on Products is waived if any addition or attachment to the Products  

do not have Hills' specific approval or are not sold as Hills products. The Products 
are designed to perform specific tasks under established test loads and unauthorised 
attachments may produce stresses for which the design is not appropriate.

9. The following applies to consumers who purchased a relevant Product in Australia:

  Our goods come with guarantees that cannot be excluded under the Australian 

Consumer Law. You are entitled to a replacement or refund for a major failure  
and compensation for any other reasonably foreseeable loss or damage.  
You are also entitled to have the goods repaired or replaced if the goods fail  
to be of acceptable quality and the failure does not amount to a major failure.

Hills Contacts

We are committed to providing you with complete customer satisfaction. If you have 
any questions or comments about our products or services please contact your nearest 
customer service centre during their local business hours:

Australia 

1300 300 564 
[email protected]

New Zealand 

09 262 3052 
[email protected]

United States 

877 534 1371 (Eastern) 
[email protected]

Europe 

+44 (0) 118 973 8971 (UK) 
[email protected]

South Africa 

021 442 1540 
[email protected]

Hills Websites

www.hills.com.au 

Hills Branded Products

www.hillsholdings.com.au 

Hills Holdings Limited

PD2278b_Heritage Secondary Standard Replacement_Manual_PRINT.indd   7

19/10/11   10:27 AM

Содержание Heritage Hoist 4









Отзывы: