background image

Mounting 

Base

Tilt Adjusting 

Screw

Bubble

Power Cord

12 VDC

Video Cable (TVI)

IR LED

Lens

Black Liner

Safty Rope

Video Cable 

(CVSB)

Keep the camera away from liquid while in use for 

non-water-proof device. 

While in delivery, the camera shall be packed in its 

original packing, or packing of the same texture. 

Mark Description 

Table 0-1 Mark Description 

Mark 

Description 

DC Voltage 

1 Introduction 

1.1 Product Features 

The camera is applicable for both indoor and outdoor 
conditions, and the application scenarios include road, 

warehouse, underground parking lot, bar, etc.. 
The main features are as follows: 

8 MP high performance CMOS sensor 

IR cut filter with auto switch 

OSD menu with configurable parameters 

Auto white balance 

Internal synchronization 

SMART IR mode 

3-axis adjustment 

1.2 Overview 

1.2.1 Overview of Type II Camera 

DC12V

IN

Enclosure

Main Body 

Mounting 

Base 

Video Cable 

(CVBS)

Power Cord 

(12 VDC)

Video Cable (TVI)

C

V

B

S

Figure 1-1 Overview of Type II Camera 

1.2.2 Overview of Type III Camera 

Figure 1-2 Overview of Type III Camera 

                    Available from A1 Security Cameras 

     www.a1securitycameras.com   email: [email protected]

Содержание TURBO HD 4K DS-2CE57U8T-VPIT













Отзывы: