8
Specification
7
6
Operation Caution and Device Maintenance
- All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related
regulations in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specification of the device for the detailed operation temperature), cold, dusty or
damp locations, and do not expose it to high electromagnetic radiation.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and
affecting the endurance of sensor at the same time.
- Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used batteries according to the instructions provided by the battery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situation.
4
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Set Up with App
5
You can view the device status including temperature, signal intensity, battery level, lid, etc.,on the device page.
Tap the button to enter the settings page.
Formatting
1. Remove the battery.
2. Hold the TAMPER button and power the detector on at the same time.
The red LED flashes 3 time when the formatting is completed.
I
nstalla
ti
on
W
all
m
ount
/
Direct touch
Ta
mp
er
p
rotec
ti
on
F
ront &
B
ack
L
E
D indicator
B
lue
(
alar
m)
Op
era
ti
ng te
mp
erature
-
10 °C to
55
°C
(
14 °
F
to 1
3
1 °
F)
-
10 °C to 40 °C
(
14 °
F
to 104 °
F)
Cer
tifi
ed
S
torage te
mp
erature
-
20 °C to 60 °C
(-
4 °
F
to 140 °
F)
Op
era
ti
ng hu
m
idity
10% to
9
0%
W
ater
p
rotec
ti
on
IP
66
Di
m
ension
(
H ×
W
× D
)
62.4
mm
x
62.4
mm
x
14.6
mm
W
ireless technology
Tri
-X
W
ireless Technology
E
nviron
m
ent te
mp
erature indicator
Y
es
2
-
way wireless co
mm
unica
ti
on
Y
es
Trans
m
ission
f
re
q
uency
868 MHz
F
re
q
uency ho
pp
ing
Mul
ti
channel trans
m
iss
ti
on
Trans
m
ission encry
pti
on
A
ES-
128 encry
pti
on
S
ignal strength indicators
Y
es
RF
range
1.2
Km
(f
ree s
p
ace
)
E
nrolling
m
ethods
P
ower u
p
,
R
e
m
ote
I
D,
QR
code
B
a
tt
ery
C
R
24
5
0
x
1
(
included
)
S
tandard ba
tt
ery li
f
e
3
years